A Barrett company - serving Glendale, CA

Tremron Driveway & Pavers in Glendale, CA

Driveway & paversDriveway & pavers
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Tremron Driveway & Pavers: The Glendale Owner’s Guide

Tremron paver driveways in Glendale typically run $7,000 to $18,000 installed, depending on square footage, base prep, and whether we’re replacing failing concrete underneath at the same time. Tremron makes products across several lines, and matching the right one to your existing installation matters more than most homeowners expect before we start. We install and repair Tremron pavers and driveways across Glendale and we can usually get eyes on a failing driveway within a few days.

Call (844) 560-4526

Owners usually figure out something’s wrong in one of two ways. Either a section of pavers has sunk low enough that the car tires catch it every time they pull in, or the joints have gone sandy and weeds are pushing through after every rain. Both point to what’s happening below the surface, not to the pavers themselves.

Barrett & Sons Construction Glendale is an independent contractor and is not affiliated with Tremron.

Which Tremron Models This Applies To

Tremron manufactures pavers across several distinct lines, and the lines are not interchangeable in the same driveway. Older installations in Glendale neighborhoods like Adams Hill and Chevy Chase often used a smaller 60mm paver in a running bond pattern, while newer builds and many of the hillside remodels we see use a 70mm or 80mm profile that handles vehicle loads differently. If you’re trying to match a failing section, the depth tells you more than the face color does. Measure the paver thickness with a tape: 60mm, 70mm, and 80mm are the common residential ranges, and a mismatched thickness will telegraph through the driveway surface within a season.

Tremron color and finish names also vary by line. The reverse of a loose paver won’t have a label or model number stamped on it, so the honest answer is that identifying the exact line usually means pulling one paver and matching profile, depth, and chamfer against current Tremron samples rather than guessing by name. On the OEM-versus-aftermarket question: for a small repair, matching an aftermarket paver of the correct depth and a close face color is often the practical call, and we’ll tell you plainly when a color won’t blend. For a full driveway, we’d use current Tremron product so the whole surface matches and ages the same way.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Tremron Driveway & Pavers Is Failing

These are the five patterns we see most in Glendale, and what’s usually behind each one.

  • Sunken or rocking pavers near the garage apron. Water running off the roof or down the slope has undermined the base sand under that section. The paver isn’t the problem; the base compaction is, and resetting the pavers without fixing the base just buys you another season.
  • Joint sand washing out after rain. Glendale’s dry stretches followed by heavy rain cycles pull polymeric or regular joint sand out faster than most owners expect. If the sand is gone, the pavers will start to shift within a few months, so it’s worth catching early.
  • Weeds or grass pushing through the joints. Persistent weeds mean the joint sand has failed and the base is likely holding moisture. That’s a sign of a drainage problem underneath, not a weed problem on top.
  • Pavers heaving around tree roots or older concrete. Common on hillside lots and where an old concrete slab sits under the pavers. The pavers lift and separate at the seams, and the fix means cutting back the root or removing the old slab section.
  • Color fading or efflorescence haze. A white powdery haze on the surface is efflorescence, moisture migrating through the paver and leaving mineral salts. It can be cleaned, but if it keeps coming back it’s telling you water is getting into the base.

Not all of these mean a full replacement. A handful of sunken pavers in one corner is often a small repair; widespread heaving across the whole driveway usually is not.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here’s what pavers and driveway work realistically cost in Glendale right now, so you’re pricing against facts instead of a phone quote.

Service Typical Glendale Range
Paver driveway installation $7,000 – $18,000
Paver patio installation $3,500 – $11,000
Driveway replacement $5,000 – $14,000
Concrete driveway installation $4,500 – $12,000
Driveway sealing $250 – $700

What pushes a paver driveway to the top of that range: the base work. Glendale lots are often sloped, and a driveway that needs six inches of compacted base, drainage correction, or removal of an old slab underneath costs more than one sitting on flat, sound ground. The paver cost is roughly a third of the job; the rest is labor, base, and hauling.

Every quote we write breaks out materials, base prep, labor, and hauling as separate line items. If something changes mid-job (say we open the base and find the original concrete failed deeper than expected), you get a written change order before we proceed, not a bigger invoice at the end. And the work is backed by our written 90-Day Done Right Promise.

DIY or Call Us?

Here’s the honest split. You can handle routine inspection yourself: walk the driveway after a rain and look for sunken sections, sweep the joints to see how much sand is left, and pull a single loose paver to measure its depth. Re-sanding joints on a sound driveway is a weekend job most homeowners can do with a broom and a bag of polymeric sand, as long as the pavers underneath aren’t shifting.

Where DIY goes wrong: resetting a sunken section without fixing the base, or trying to pound a mismatched-thickness replacement paver into an existing field. Paver driveways are a structural system, not a tile floor, and a poorly compacted patch will telegraph within a year and crack the adjacent pavers. If you’ve got widespread heaving or the base is suspect, that’s a job for someone with a plate compactor and a transit. Call (844) 560-4526 and we’ll tell you honestly whether it’s a $400 re-sand or a rebuild.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 560-4526
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Barrett & Sons Construction Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch