A Barrett company - serving Glendale, CA

5 Mistakes to Avoid With Fence Installation

November 14, 2026 • Barrett & Sons Construction Glendale

5 Mistakes to Avoid With Fence Installation

5 Mistakes to Avoid With Fence Installation

The most expensive fence mistake we get called to fix wasn’t bad materials or sloppy posts. It was a brand-new $9,000 fence that had to come out because nobody pulled a permit, and the neighbor filed a complaint the week it went up. Most fence installation mistakes in Glendale aren’t made during installation at all. They’re made in the first 30 minutes, before a single hole is dug. Get the permit check and the neighbor conversation right and you head off most of the headaches that follow. If you’d rather not gamble on that, call (844) 560-4526 and we’ll walk you through it.

Call (844) 560-4526

Key Takeaways

  • Pull the permit before you dig. A fence built without one can be ordered removed at your cost.
  • Confirm the true property line from the plat map, not from where the old fence sat.
  • Glendale’s expansive clay soil punishes rule-of-thumb post depth. Depth has to match your soil, not just your fence height.
  • Price the fence on maintenance over ten years, not the sticker at the lumber yard.
  • Get a written change-order clause. Verbal “go ahead” on an upgrade is how disputes start.

1. Skipping the Glendale Building Permit Process

Most residential fences in Glendale need a permit, and the rules hinge on height and location. A fence in your front yard is held to a lower height limit than one in the backyard, and corner lots have sight-line rules at the driveway that catch people off guard. Before you buy a single board, spend ten minutes at the city’s online permit portal or call the building department and ask two questions: what’s the maximum height allowed where this fence goes, and does this project need a permit? You’ll usually have your answer the same day.

Here’s what happens when you skip that step. A neighbor who doesn’t like the look of your new fence calls the city. An inspector comes out, measures, and finds no permit on file and a fence that’s over the allowed height. You get a notice to remove it. That’s the $9,000 story from the top of this page, and it’s not rare in Glendale, where lots are tight and fences sit close to property lines.

The permit itself isn’t the enemy. It’s cheap insurance. When the inspector signs off, you have a document that says your fence is legal, and that document matters when you sell the house. Ask yourself which is easier: a short visit from the inspector now, or a demand to tear out a finished fence later.

2. Not Establishing the True Property Line Before Demo

Old fence position is not property line. We can’t tell you how many times a homeowner has pointed at a leaning fence and said “that’s the line,” only to find out it was two feet onto the neighbor’s side. Read the plat map before anything gets torn out. Your county recorder’s office has it, and the map shows the actual lot dimensions and where the line runs in relation to your house and any recorded easements.

To read it correctly in Glendale:

  1. Pull the plat map for your parcel from the county recorder, not a screenshot from a listing site.
  2. Find the measured distances from your house corners to the property line, not just the lot’s overall width.
  3. Measure those distances on the ground with a tape from the same reference points the map uses.
  4. If the numbers don’t match the old fence, believe the map. If they don’t line up at all, hire a licensed surveyor before you dig.

This is also where the neighbor conversation belongs. A five-minute chat about where the line actually runs, done before demo day, prevents a boundary dispute that can outlast the fence by years. A fence on the wrong line isn’t just an inconvenience. It can become a legal fight.

3. Choosing Post Depth by Fence Height Alone

The old rule of thumb says bury a third of the post, so a 6-foot fence gets a 2-foot hole. That rule was written for stable, well-drained soil. Glendale’s expansive clay is neither. That clay swells when it’s wet and shrinks and shifts when it dries, and it moves posts that were set to a height-only formula. A fence that looks fine in spring can lean by the end of a dry summer.

What actually holds in Glendale clay:

  • Deeper holes than the height rule suggests, sized to your specific soil, not a generic chart.
  • Concrete footings with a bell shape at the bottom so the post resists frost-free heave and clay movement.
  • Posts set below the local frost line and below the active clay layer, which is deeper than most homeowners expect.
  • Proper drainage so water doesn’t pool at the base and turn the clay to soup.

Setting posts is the part of the job that’s hardest to fix later, so it’s worth doing right the first time. This is also a genuinely physical job with buried utilities in play. Call 811 before you dig, every time, no exceptions.

4. Picking Material on Upfront Cost Instead of Glendale Maintenance Reality

Wood is the cheapest fence to buy and the most expensive to live with in Glendale. Our summers are hot and dry, our winters bring rain, and the UV here fades and dries out untreated lumber fast. A cedar fence that looks great at install can need staining every couple of years and start to cup and split within a decade. Vinyl handles the sun better but can get brittle in sustained heat. Ornamental metal lasts longest but costs the most up front.

The smarter math is a ten-year number. Add the purchase price, the stain or sealant you’ll buy, and the weekends you’ll spend on it. A wood fence that costs less to install but demands restaining every other year often costs more over ten years than a vinyl or metal fence that just needs a rinse. Factor in wind exposure too: open lots and hillside properties in Glendale take more wind load, and a fence built for a sheltered yard will rattle and loosen on an exposed one. Match the material to your site, not just to the quote in front of you.

5. Signing a Contract Without a Written Change-Order Clause

Verbal approval for an upgrade is how fence disputes are born. You ask for taller posts or a nicer gate, the crew says “sure,” and three weeks later there’s a bigger invoice than the one you signed. Our rule is simple: every scope, every allowance, every price change arrives as a written change order before the work happens. An allowance that isn’t on paper is a surprise waiting for a date.

Before you sign any fence contract, check for these:

  • A written change-order clause that says no scope or price change happens without your signature first.
  • Line-item pricing for posts, panels, gates, concrete, and hardware, not one lump sum.
  • A stated permit responsibility line, so you know who pulls it.
  • A written workmanship guarantee with a clear call-back process.

The contractor you hire should put it all in writing and stand behind it. That’s why we back every fence we build with our written 90-Day Done Right Promise. If something’s not right, one call brings us back.

When to Call a Pro

Some of this you can do yourself: the permit phone call, the plat map check, the neighbor chat. But once you’re reading clay behavior, footing depth, and sight-line rules on a corner lot, the stakes go up. A fence is a buried structure, and getting the footings and the line wrong is expensive to undo. That’s the moment to bring in a crew that pulls permits and inspects the work, not the cheapest bid at the door. If you’re in Glendale and want a fence that passes inspection and holds up to the soil and the sun, we’re glad to help.

Related services in Glendale: Fence Installation in Glendale for the full build process, and Driveway & Pavers in Glendale if you’re reworking the front of the property at the same time.

The Bottom Line

The fence mistakes that cost the most rarely happen during installation. They happen in the first half hour: the permit you didn’t pull, the property line you trusted instead of measuring, the post depth you guessed at, the material you priced on day one instead of year ten, and the change order you approved with a handshake. Get those five right and the rest of the job tends to go smoothly.

At Barrett & Sons Construction Glendale, we’ve been doing this since 1998, and the things we see go wrong on fences are almost always preventable. If you’re in Glendale and need help, Barrett & Sons Construction Glendale offers free estimates, permits pulled and inspections signed on every eligible job, and written change orders before any scope change. Call (844) 560-4526 to get started.

Frequently Asked Questions

Need Construction Help?

Call Barrett & Sons Construction Glendale - licensed & insured, here with fast after-hours help in Glendale.

(844) 560-4526
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Barrett & Sons Construction Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch