A Barrett company - serving Glendale, CA

Ameristar Construction Service in Glendale, CA

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Why Glendale Homeowners Choose Ameristar Construction

We provide independent Ameristar construction and cabinet service in Glendale, CA, with no affiliation or authorization from Ameristar. What makes our Ameristar work different is that we treat it as a builder-grade product line we know inside out, from the RTA shaker boxes and assembled oak and maple lines to the thermofoil-front value-series cabinets and pre-hung door slabs. Glendale is a built-out city where almost every project is a remodel, addition, or hillside rebuild, so the cabinet work here is usually a retrofit into an existing kitchen, not a fresh install. That takes a crew that knows where Ameristar products fail and how to specify around those weak points. Call (844) 560-4526 for a free estimate.

Call (844) 560-4526

Our technicians have up to 28 years of experience, and we’re state-licensed and insured, with written line-item quotes before any work begins.

Why Trust Barrett & Sons Construction Glendale for Your Ameristar Construction?

Ameristar cabinets aren’t complicated, but they’re unforgiving of shortcuts. The RTA shaker line goes together with cam locks and thin back panels, and if it’s assembled or re-set on a floor that isn’t level, the whole run racks out of square and the doors never sit right again. We’ve handled enough of these runs to know that a door that drags six months after installation usually isn’t a hinge problem, it’s a box problem underneath. We match OEM Ameristar door fronts and boxes when a single cabinet needs replacing so the run stays visually consistent, but we upgrade the hinges, drawer slides, and shelf hardware. The factory hardware is where the value line cuts the most corners, and better slides and hinges outlast the cabinet face itself.

For warranty safety, we follow the manufacturer’s installation specs for clearances, mounting, and moisture protection, because we don’t have the power to maintain a warranty for Ameristar but we can absolutely protect your right to make a claim under it.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Common Ameristar Construction Problems We Fix in Glendale

Most of what we see on Ameristar cabinets in Glendale falls into five repeat patterns. None of them are mysterious once you know what to look for.

  • Thermofoil skins peeling at the edges near the range and dishwasher. The value-series thermofoil doors lift where heat and steam cycle constantly against the edge banding. Once it starts, it curls back further every month, and touching it up with glue only buys time.
  • RTA shaker boxes racking out of square. Cam-lock assembly with a thin back panel means a cabinet that wasn’t set dead level will twist under load. Doors start dragging, drawer fronts gap, and no amount of hinge adjustment fixes a box that’s gone out of square at the carcass.
  • Particleboard and MDF bases swelling under sinks. A slow trap or supply-line leak goes unnoticed for weeks and the particleboard base swells and never shrinks back. We pull the base cabinet, dry out the cavity, find the actual leak source, and then decide whether the box can be saved or has to come out.
  • Builder-grade hinges and slides wearing out. Ameristar factory hinges and slides on the value line start to sag well before the cabinet face itself fails. The whole run feels loose because the mechanism is tired. Quality replacements usually bring a run back for years.
  • Door slabs out of alignment on the assembled oak and maple lines. Solid wood doors on assembled cabinets still move with Glendale’s dry summer air and the swing between heating seasons. A box that was fine in April drags in September. Seasonal adjustment is real maintenance, not a defect.

Pulling a door on a typical Ameristar cabinet job usually reveals cam-lock boxes that have racked and particleboard bases that swelled after a slow under-sink leak. A qualified local pro checks whether the boxes are structurally sound before recommending refacing, re-squares and re-hangs what’s salvageable, and specs new boxes and quality slides for the rest. That check is the whole job. Skip it and you’re refacing a sinking ship.

Ameristar Parts & Our Repair-vs-Replace Approach

We don’t keep Ameristar stock on hand, so parts are ordered to the specific model and finish code on your cabinet. When you need a single door front or a matching box, we pull the label and order against it rather than buying a “close enough” finish. That matters more than people think, because a mismatch in a satin oak finish is visible from the doorway.

For the working pieces, we spec quality aftermarket hinges, slides, and shelf hardware because the factory components are the weak link. The door front and box are worth matching OEM; the mechanism underneath isn’t.

Refacing versus replacing is where we’re honest with you. If one cabinet box has swollen or one door has started to peel, we repair and reface and leave the run intact. If two or more boxes have swollen or the skins are peeling across a full run, replacement beats refacing. Refacing over failing substrate just traps the problem behind a nice new veneer. Call (844) 560-4526 and we’ll tell you which one you’re looking at after a look at the boxes, not before.

Our Ameristar Service Process – Step by Step

  1. 1
    Diagnosis. We open doors, pull drawers, and check the boxes for square, swelling, and racking. We look at the finish code on the label and confirm whether the door fronts are RTA shaker, assembled oak and maple, or thermofoil value-series, because each has a different repair path.
  2. 2
    Written scope and pricing. Every cabinet line, every allowance, every price change shows up on paper before work starts. If we discover a swollen base cabinet after demo reveals more, you get a written change order before we touch the next box.
  3. 3
    Repair or install. We re-square and re-hang what’s salvageable, swap hardware to quality slides and hinges, and install new Ameristar boxes or door fronts where the substrate has failed. Doors get hung and adjusted on site, not in a warehouse.
  4. 4
    Test run. Every door and drawer gets cycled fully open and closed. We check that fronts align across the run, drawers roll without binding, and nothing racks when the full load goes in.
  5. 5
    Warranty handoff. You get the written workmanship warranty on the install, and we leave you the model and finish codes for any future parts order.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Ameristar Products We Service & Install in Glendale

We service and install the Ameristar RTA ready-to-assemble shaker cabinets, the assembled oak and maple cabinet lines, and the value-series laminate and thermofoil cabinet fronts. We also hang Ameristar pre-hung entry and interior door slabs, including re-hanging and adjusting existing slabs where the frame has shifted. On the cabinet side, we install and reface the full run in both kitchens and laundry rooms, and handle cabinet installation on its own when the rest of the room is staying put. In Glendale, that standalone install is often the real job, since most homeowners here are updating a 1940s or 1960s kitchen rather than building new.

We Also Service These Brands

We’re not tied to one cabinet line. We work with KraftMaid, Cambria, and Silestone daily, plus Kohler fixtures on the plumbing side. That means when we tell you Ameristar is right for your Glendale kitchen or that a KraftMaid upgrade makes more sense for the run, the advice comes from product-neutral experience rather than brand loyalty.

FAQs – Ameristar Construction Service in Glendale

Service Typical Price Range
Cabinet Installation $4,000 – $13,000
Full Kitchen Remodeling $14,000 – $45,000
Small & Partial Kitchen Remodels $9,000 – $20,000
Countertop Installation $2,000 – $6,500
Backsplash Installation $800 – $2,500

Call (844) 560-4526 for an exact quote on your Glendale kitchen – estimates are free.

Book Your Ameristar Service in Glendale, CA

If your Ameristar cabinets are peeling, racking, or swelling under the sink, we can tell you honestly whether repair and refacing makes sense or whether replacement is the only fix. We’re state-licensed and insured, and every job ends with a written workmanship warranty. Call (844) 560-4526 to schedule your free estimate.

Written by the team at Barrett & Sons Construction Glendale.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 560-4526
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Barrett & Sons Construction Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch