Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Home Additions & ADU: The Glendale Owner’s Guide
If you’re planning a KraftMaid-outfitted addition or ADU in Glendale, plan on $45,000 to $130,000 for a home addition and $90,000 to $220,000 for a full ADU, depending on size, foundation work, and how much of the interior gets KraftMaid cabinetry. When the cabinetry inside that addition starts failing – doors that won’t stay shut, drawers that grind, a cabinet box pulling away from the wall – it’s usually a hinge, a glide, or a sagging anchor, not the cabinets themselves. We match the replacement part to your KraftMaid line, quote it in writing, and install it so the addition works the way it did the day it was finished. Call (844) 560-4526 to schedule a free estimate.
Barrett & Sons Construction Glendale is an independent service provider. We’re not affiliated with KraftMaid, and we don’t claim to be.
Which KraftMaid Models This Applies To
KraftMaid has built cabinetry under several lines over the years, and the part you need depends on which one is in your addition. The two families Glendale owners most often bring us are the semi-custom lines (KraftMaid’s standard door-and-box program, sold through big-box and dealer channels) and the full-access and frameless styles, where the hinge and glide hardware is completely different from the framed line. Before you order anything, find the label inside a cabinet door or on the back of a drawer box. It lists the series and often a date code. If the label is gone, measure the cabinet opening and the door overlay – a 1/2-inch overlay hinge will not fit a 1-1/4-inch overlay door, and that mismatch is the single most common wrong-part order we see.
On OEM versus aftermarket: for structural box parts and anything load-bearing in an ADU kitchen, we source the KraftMaid-spec equivalent. For hinges, glides, and bumpers, a quality aftermarket part from a reputable hardware maker is often better than the original and costs less. Ask before you buy – we’ll tell you which side of that line your part falls on. Glendale homes with hard water and dry inland heat tend to wear glides faster than coastal installs, so we favor sealed bearings here.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Home Additions & ADU Is Failing
- Doors that drift open or won’t close flush. The hinge has lost tension or the mounting screws have stripped out of the box. In Glendale’s dry summer air, the wood in a cabinet box shrinks slightly, and stripped screw holes get worse fast.
- Drawers that grind or stick halfway. The glide’s rollers have flattened or debris has packed the track. Undermount glides on KraftMaid full-access drawers are the usual culprit, and they fail quietly before they fail completely.
- A cabinet pulling away from the wall. The anchor screws behind the box have worked loose. In an addition or ADU with a newer stud wall, this often traces to anchors that were set into drywall instead of framing.
- Soft-close that slams. The damper cartridge inside the hinge or glide is spent. KraftMaid’s soft-close hardware has a service life, and when the dampers go, every door in the addition announces it.
- Sagging shelves or a racked box. The shelf pin or the box corner has failed under load. This one is worth a look before you load the cabinet again, because a racked box can crack the door frame.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most KraftMaid hardware replacements in a Glendale addition run $150 to $400 per cabinet when we swap hinges, glides, and dampers together. A single hinge or glide set is typically $40 to $90 installed. When the problem is bigger – a whole run of cabinets in a new ADU kitchen, or a cabinet box that needs re-anchoring to framing – you’re into cabinet installation territory, which runs $4,000 to $13,000 in Glendale, and a full kitchen inside an addition lands at $14,000 to $45,000.
What drives the range: how many cabinets are involved, whether the hardware is OEM or a sealed-bearing aftermarket equivalent, and whether we’re re-anchoring to framing or replacing a box. Every quote is line-item, written, and fixed. Any scope change arrives as a written change order before we touch the cabinet. The work carries our written 90-Day Done Right Promise, and a free second opinion on any written estimate you’ve already got.
DIY or Call Us?
You can safely check a few things yourself: open the door and look for the label, check whether the hinge screws turn freely or spin, and confirm the drawer glide is clean and seated in its clip. Those checks cost nothing and tell you a lot. Where it goes wrong is in the swap itself. KraftMaid’s cam-and-clip hinge systems have specific adjustment sequences, and a wrong turn on the eccentric cam strips the mounting plate. Re-anchoring a cabinet to framing means finding the studs behind a finished addition wall, which is where most homeowners call us after a failed attempt.
There’s no injury risk in cabinet hardware, but there is a real risk of cracking a door frame or stripping a box if the part is forced. If the cabinet is pulling off the wall, stop loading it and call. Glendale owners can reach us at (844) 560-4526 for a free estimate – a live person answers, day or night.
FAQs
Expect 10 to 15 years from hinges and glides under normal use, and less in a busy ADU kitchen. Glendale’s dry inland air and hard water speed up wear on dampers and glide rollers, so we often see hardware fail closer to the 8-to-10-year mark here. If yours is past that and slamming or grinding, it’s time to replace – call (844) 560-4526 for a quote, and estimates are free.
Often, yes. A loose hinge can sometimes be re-set with a longer screw or a hardwood plug in the stripped hole, and a sticking glide can be cleaned and re-seated. A cracked damper or a flattened roller cannot be repaired – it has to be replaced. We’ll tell you honestly which situation you’re in before we quote anything.
A single hinge or glide set is a 20-to-30-minute job. A full cabinet’s worth of hardware takes about an hour, and a whole kitchen run in a Glendale addition is usually a half-day to a full day. We schedule around your household, not the other way around.
We match by the label and by measured overlay, not by guesswork. If the label is gone, we measure the opening and the door overlay, then order the KraftMaid-spec equivalent or a sealed-bearing aftermarket part that fits the same mounting pattern. You get the part number and price in writing before we order. Call (844) 560-4526 to get started; a free estimate is the first step.
We also work with Cambria, Silestone, and Kohler when a KraftMaid addition or ADU project calls for countertops and fixtures alongside the cabinetry. Our technicians have up to 28 years of experience, every eligible job includes permits pulled and inspections signed, and Glendale homeowners can look up our license number before they sign anything. Call (844) 560-4526 for your free estimate.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.