Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Kohler Fence Installation: The Glendale Owner’s Guide
Fence installation in Glendale with Kohler-branded components runs $3,500 to $9,000 installed, and the exact number depends on linear footage, material, terrain, and whether the old fence and footings have to come out. On a straightforward fence replacement in Glendale, we can often walk the property, measure, and hand you a written estimate the same day you call. Kohler fencing hardware shows up on gates, latches, posts, post caps, hinges, and rail brackets, and it’s one of the better lines going.
Most Glendale owners find out something has failed the same way. You go to close a gate and it drops half an inch and won’t catch. A latch throws and springs back but won’t hold. A gate starts dragging on a concrete pad in the summer and you think the post has moved. Or you notice the fence line leaning after a Santa Ana wind event and you’re not sure whether it’s the post footing or the hinge side of the gate. That’s usually the point where you start looking for the part instead of your old contractor.
Barrett & Sons Construction Glendale is an independent contractor. We install and service fences built with Kohler components, and we’re not affiliated with Kohler. When you call, a live person answers, day or night.
Key Takeaways
- Installed Kohler-component fence work in Glendale runs $3,500 – $9,000 depending on footage and material.
- Most “failed” Kohler parts we see are actually footing, post-plumb, or hinge-alignment issues, not the part itself.
- Every scope, allowance, and price change arrives as a written change order before work starts.
- We pull permits for eligible work and get inspections signed, every time.
- Every job backs up to the written 90-Day Done Right Promise: one call brings Tom back if something isn’t right.
Which Kohler Models This Applies To
Kohler makes fence hardware and gate components that get sold under model and series designations, and those part numbers matter more than most homeowners realize. Two latches that look identical on the shelf can be spec’d for different gate weights or different post profiles. Two hinges with similar plates can be drilled for different screw patterns, which means the old holes on your post won’t line up with the new hardware. Before you order anything, find the label on the old part (it’s often on the hinge barrel or inside the latch body) or measure the gate width and post thickness. That measurement narrows the field faster than any part number search. On original-vs-aftermarket: for a gate that sees daily use, buy the Kohler-original equivalent for latches and hinges. For rail brackets and decorative caps, a quality equivalent from a known brand is a reasonable call, and we’ll tell you honestly which way we lean for your specific gate. Glendale gates that take a beating in wind or sun are the ones where brand matters most.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Kohler Fence Installation Is Failing
Here’s what a failing Kohler fence installation actually looks like in Glendale, and what each symptom usually means:
- Gate drops and won’t latch cleanly. Almost always hinge wear or a gate that’s out of alignment because the post has moved. If the hinge plate is bent, the part failed. If the gate sags straight down, the hinge is a symptom, not the cause.
- Gate drags on the ground or the pad. Post footing has settled or heaved. Common on Glendale lots where the footing was poured shallow during the summer dry season.
- Fence line leaning after a wind event. In Glendale, the foothill neighborhoods and canyons catch Santa Ana winds hard. A leaning post most often means the footing is under-sized or the post was set without enough cure time before loading.
- Rattling or wobbling at the hinge side. Hinge screws have wallowed out the wood or metal post. Sometimes a longer screw fixes it temporarily, but the hole doesn’t heal, and the wobble pulls out the next screw in line.
- Rust on the latch or hinges within a few years. Glendale’s heat and dry air don’t cause much rust on their own, but sprinkler overspray and coastal marine layer that drifts inland can. A coated latch that goes back to bare steel is on its way out.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For fence installation and replacement work in Glendale involving Kohler gate components, our installed range is $3,500 to $9,000. Here’s how that number breaks down and where it moves:
- Linear footage and fence height: a 40-foot side fence in a standard height sits at the low end; a full perimeter or a taller privacy fence pushes toward the top.
- Material: wood and vinyl run lower up front; composite and metal hardware systems with Kohler hardware run higher. We confirm material and hardware allowances in writing before work starts.
- Footing work: removing and re-pouring post footings when the old ones are failed adds real labor and concrete, and we tell you that up front.
- Gate build and hardware: a single gate with a Kohler latch and hinges is a smaller line; a double-drive gate with Kohler hardware leans heavier.
- Permits: where Glendale requires a fence permit on your property, we pull it and get the inspection signed.
You get the estimate in writing, line by line. If a scope change comes up mid-job, the number goes in a written change order before anyone touches the fence. Any allowance that isn’t on paper is a surprise waiting for a date, so everything goes in writing.
DIY or Call Us?
There are things you can safely check yourself and things you shouldn’t try. You can measure your gate, tighten visible screws on the hinge side, and clean a latch that’s binding up on grime. You can walk the fence line with a level, or take a photo of the label on the failing part, and those checks help us quote accurately. Where it goes wrong: digging out and re-pouring post footings is the number one problem. A footing that’s too shallow, set into soft dry soil, or cured too fast will fail again within a season or two, and the labor is wasted. Gate alignment without understanding the load on the post can also make things worse. If you’ve snugged the screws and the gate still drops, call (844) 560-4526 and we’ll come out and figure out whether it’s the part or the post.
FAQs
Coated Kohler gate hardware typically lasts 8 to 15 years in Glendale’s climate, but the post footing lifespan is usually shorter and dictates how long the whole system stays plumb. If your footing was set shallow, the practical life of the whole fence is limited by the footing, not the latch or hinge. Call (844) 560-4526 for an exact quote, and the estimate is free.
Often yes. A latch that’s misaligned or a hinge that’s snugged with the right screws can sometimes be saved. What can’t be saved is a hinge plate that’s bent under load, a latch body cracked at the strike, or hardware that’s rusted through. We’ll tell you on the visit whether a repair makes sense or whether we’re putting new hardware on a failing post. Call (844) 560-4526 for a free estimate.
A single gate retrofit with Kohler hardware typically takes half a day, while a full fence replacement runs one to four days depending on linear footage, footing work, and whether a permit inspection is scheduled. Glendale inspections add time and we schedule them in advance, so the delay doesn’t hit mid-job. Call (844) 560-4526 to get your estimate and a realistic schedule.
We identify the correct Kohler part number from the label or the gate measurement, then source it from a supplier we’ve worked with. We don’t stock parts locally and we don’t carry them on a truck, so ordered parts usually arrive in a few days to a week. That timeline goes in your written estimate so you know what to expect. Call (844) 560-4526 to get started.
We also work with KraftMaid, Cambria, and Silestone if your project runs past the fence line into the house. Ask anyone on your street about us, or look up the license number yourself. Barrett & Sons Construction Glendale has been owner-operated since 1998, every price change is a written change order, and every completed job carries the 90-Day Done Right Promise. Call (844) 560-4526 for a free estimate today.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.