A Barrett company - serving Glendale, CA

Moen Roofing in Glendale, CA

RoofingRoofing
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Moen Roofing: The Glendale Owner’s Guide

Moen makes faucets and shower valves, not roofing materials, so if you’ve landed here looking for a “Moen roofing” part, the honest answer is that there isn’t one: what you’re replacing is almost certainly the roof flashing, vent boot, or pipe collar near a plumbing stack or skylight, and the Moen connection is the fixture underneath it. Installed roof repair in Glendale runs $400 – $1,800 for the sorts of penetrations and leak points that get blamed on “the Moen,” and full roof replacement runs $8,000 – $20,000 when the decking has rot behind it. Most Glendale owners discover the failure the same way: a brown water stain spreading across a bathroom ceiling directly below a Moen shower valve or tub spout, or a drip they hear in the wall after a rain.

Call (844) 560-4526

Barrett & Sons Construction Glendale is an independent service provider and is not affiliated with Moen. We install and repair the roofing and flashing around plumbing penetrations, and we source Moen-compatible fixtures and trims through the same supply channels our crews have used across Glendale for years.

Which Moen Models This Applies To

The Moen products that intersect with roofing work fall into a few recognizable families, and matching the right trim or escutcheon to the existing rough-in valve matters more than the model number on the box. Moen’s Posi-Temp valves (the 1222, 1225, and 1200 series cartridges) show up in the vast majority of Glendale homes built between roughly 1985 and 2015, and the escutcheon plates that cover the wall penetration behind them vary by valve body, not by trim style. If you’re replacing a Moen shower valve and the roof stack above it at the same time, the rough-in depth (typically 2-3/4 inches to 3-1/4 inches from the finished wall) determines which replacement will seat correctly without cutting back the drywall.

The OEM-versus-aftermarket call is straightforward for Moen: stick with genuine Moen cartridges and trim kits for the interior fixtures when the rough-in valve is Moen, because the tolerances on a 1222 cartridge are tight enough that a $30 knockoff will weep within two seasons. For the roof-side pieces (flashing, boots, collars), brand-name isn’t the variable; the variable is lead vs. no-lead and the boot material, which we’ll cover below. Identify the Moen side by pulling the trim and reading the stamp on the valve body, then match the replacement to that stamp, not to the trim you’re removing.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Moen Roofing Is Failing

Glendale’s climate is the real story here. We average 21 inches of rain a year, almost all of it between November and March, and summer highs routinely push past 95°F in the Verdugo foothills. That wet-dry cycle is brutal on the rubber boots and lead flashing around roof penetrations, and the failure usually shows up on the plumbing side first.

  • Water stain on the ceiling below a Moen shower valve. The culprit is almost always the pipe boot or lead stack flashing at the roof penetration, not the valve itself. The Moen cartridge is where the water enters the wall cavity, but the leak at the roof is where it enters the house.
  • Drip you hear but can’t find. A slow leak at a boot collar drips down the plumbing stack and shows up at the ceiling cutout around the shower trim plate. If you hear it only during rain, the roof is the source; if it runs constantly, the Moen cartridge itself is failing.
  • Cracked or sun-baked rubber boot around the pipe. Glendale’s UV load splits a standard EPDM boot at the collar within 8 to 12 years on a south or west-facing slope. Once it cracks, water shears past the pipe and into the attic.
  • Stain ring around the shower escutcheon plate. Water tracking down the outside of the supply pipe from a failed roof flashing follows the pipe and leaves a mineral ring at the trim. Pale, crusty deposits mean hard water intrusion from the roof side, not the shower side.
  • Musty smell in the bathroom after rain. Wet insulation and framing in the attic cavity above the Moen fixture will smell within 48 hours of a Glendale storm. If the smell tracks with the weather, pull the trim plate and look up.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Glendale pricing for the work that sits behind a “Moen roofing” search falls into three honest buckets. Roof repair, including the flashing, boot, and collar replacement around plumbing penetrations, runs $400 – $1,800 installed. Tile roof repair, which is common here because so many Glendale homes have clay tile in the foothills, runs $600 – $2,500 because matching and re-bedding the tile is the slow part. Roof replacement, when the decking behind the penetration has rotted and the fix becomes a full tear-off and re-roof, runs $8,000 – $20,000 for a typical Glendale home. Metal roof installation, if you’re moving off shingle or tile, runs $15,000 – $40,000.

What drives the range: roof pitch, tile type, the number of penetrations, whether the decking is soft, and whether the repair uncovers a second issue at the same stack. Every Barrett & Sons scope is in writing before any work starts, and every price change arrives as a written change order before a nail moves. Our 90-Day Done Right Promise is on the contract, not in fine print.

DIY or Call Us?

Here’s the honest split. You can safely check the interior side: pull the Moen trim plate, look for a stain ring or crusty mineral deposits, and feel for soft drywall. You can look in the attic with a flashlight after a rain and trace a drip back to the pipe penetration. That much is diagnostic, not dangerous.

What you should not do is climb a wet roof to replace a boot or lead flashing yourself. Roof work at any pitch on a Glendale home with clay tile is a fall hazard, and a badly seated boot will leak worse than the failed one you’re replacing. Climbing wet tile on a November morning is how people end up in the ER. This is a job for a crew with the right harnesses and the right flashing inventory.

Call (844) 560-4526 and we’ll schedule a diagnosis. Your free second opinion on any written estimate you’ve already received is good to use here, and we honor it even if you don’t hire us.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 560-4526
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Barrett & Sons Construction Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch