Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Glendale Owner’s Guide
If you’re pricing Schluter bathroom remodeling in Glendale, a full bathroom runs $9,000 – $28,000 installed, and a small bathroom lands between $5,000 – $12,000. A walk-in shower built with the Schluter system typically runs $4,500 – $12,000, and a tub-to-shower conversion $3,500 – $10,000. This isn’t emergency repair work, so we schedule these jobs rather than promise same-day turnaround. Call (844) 560-4526 and we’ll set a free estimate at a time that works.
Most Glendale owners discover a Schluter problem the same way. A grout line near the shower curb keeps darkening no matter how often it’s scrubbed. A tile sounds hollow when you tap it. Or the caulk joint where the floor meets the wall pulls away every few months. Those are rarely tile problems. They’re almost always water getting behind the surface and finding the weakest layer in the assembly. In a Schluter system, that layer is usually the bonded waterproof membrane or the drain flange connection, and once it’s compromised the damage spreads quietly under a floor that still looks fine from above.
Which Schluter Models This Applies To
Schluter isn’t one product. It’s several systems that get mixed and matched, and knowing which one is under your tile changes how the repair gets scoped.
- Kerdi and Kerdi-Band: the thin sheet-applied waterproofing membrane and its seam tape. Common in showers and full wet rooms. The 5-inch and 7-inch band widths are not interchangeable at a change of plane, and using the wrong width at an inside corner is one of the most frequent install mistakes we correct in Glendale.
- Kerdi-Board: the foam tile backer with the membrane already bonded to it. Sold in 1/2-inch and 3/8-inch thicknesses. If a wall was framed out of plumb, a crew can sand or shim this board to square. Over time, a poorly anchored panel can flex and crack grout lines above it.
- Ditra and Ditra-XL: the uncoupling membrane for floors, the XL version for larger-format tile. Glendale floors over a post-and-beam subfloor often need Ditra to isolate movement from the tile above.
- Kerdi-Line and Kerdi-Drain: the linear and point drains, with the integrated bonding flange that the membrane ties into.
To identify what you have, look at the edge of a removed tile or lift the drain grate. Kerdi has a printed fleece backing with a repeating logo. Kerdi-Board is a rigid foam core with an orange face. Ditra is orange with a grid of dovetail cavities. If the label is gone, measure the thickness and match it to Schluter’s published spec sheet before ordering anything. Our techs have up to 28 years of experience reading these systems, and they’ll tell you straight when an OEM part is the only safe choice and when a quality equivalent does the same job for less.
On OEM versus aftermarket: Schluter is a system, and the parts are engineered to work together. A generic drain flange or a knockoff membrane roll may look close enough on a shelf, but the bonding fleece differs, and the seam won’t hold the way the real product does. For the membrane, band, and drain, we specify Schluter. For thinset and grout, we use quality brands that meet Schluter’s published requirements. Barrett & Sons Construction Glendale is an independent service provider, not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
Here’s what a failing Schluter assembly actually looks like in a Glendale bathroom. Each symptom has a cause, and the cause tells you how deep the repair goes.
- Grout that keeps darkening near the curb or drain: water is getting behind the tile and wicking up through the grout, which means the membrane or the drain flange seal has opened. Scrubbing won’t fix it.
- Hollow-sounding tile: tap with a screwdriver handle. A hollow note means the thinset didn’t bond, or the membrane has separated from the substrate. Tile over a loose membrane will eventually crack.
- Loose or lifting Kerdi-Board seams: usually a fastener pattern too sparse or thinset that was mixed wrong. The panel moves, the seam tape fails, and water gets in at the joint.
- Water stains on the ceiling below, or a soft spot in the subfloor: a slow leak from the drain flange or a failed membrane tie-in. By the time you see it downstairs, the damage has been running for weeks.
- Mildew that returns in the same corner every season: the wet area isn’t drying because moisture is trapped behind tile. Glendale’s warm inland air makes the surface look dry while the assembly stays wet underneath.
One Glendale-specific reality worth knowing: our warm, dry summers and damp winters swing the framing. In older homes near Adams Square and Chevy Chase, that movement is a common cause of grout cracks and membrane seams pulling apart over several years. It’s not always an install error. It’s the building working.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Glendale, a bathroom remodel that includes correcting a failed Schluter assembly runs $9,000 – $28,000 depending on scope. A full small bathroom runs $5,000 – $12,000. Focused repair work is smaller: a shower replacement is $3,000 – $8,500, and a walk-in shower installation is $4,500 – $12,000.
| Scope | Typical Glendale Range |
|---|---|
| Full bathroom remodel (Schluter system) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
What moves the number: how much tile has to come out to reach the failure, whether the drain needs relocating, and whether the subfloor needs repair once it’s opened up. Our pricing comes as a written line-item estimate before any work starts. Every scope change and every allowance is in writing before it touches the job. The work is backed by the written 90-Day Done Right Promise, so if something isn’t right after we finish, one call brings the crew back.
DIY or Call Us?
There’s real danger in tearing into a shower assembly, and it’s not the spring-loaded kind. It’s the structural kind: a waterproofing membrane surrounds a finished bathroom. If a homeowner cuts into it and doesn’t re-waterproof correctly around the drain, they create the exact leak pattern that destroyed the floor in the first place. That’s a lot of risk for a part that costs less than the repair.
What an owner can safely check:
- Tap the floor and walls to find hollow spots.
- Look at the grout lines and caulk joints for recurring cracks.
- Check the ceiling below the bathroom for stains or a soft feel.
- Lift the drain grate to read the model.
- Watch for a musty smell that doesn’t clear after cleaning.
Where DIY goes wrong: re-setting a drain flange or re-bonding membrane without the right thinset mix and cure time. Water gets behind it and the failure returns in a few months. If you’ve found the problem, call (844) 560-4526. We’ll schedule a free estimate and tell you honestly whether it’s a repair or a rebuild.
FAQs
A properly installed Schluter assembly should hold for 20 years or more; the membrane and board don’t wear out on their own. The failure points are at the seams, drains, and tile joints, plus movement in the framing. Call (844) 560-4526 for a free estimate if yours is showing symptoms.
Sometimes it can be repaired, if the failure is isolated to one seam or a rough drain flange and the surrounding tile is still bonded. If water has traveled under the floor, the assembly usually comes out. Estimates are free, so call (844) 560-4526 and we’ll tell you which one you’re looking at.
A localized repair runs one to three days including cure time. A shower rebuild that replaces the membrane and tile from the pan up runs five to ten days. Call (844) 560-4526 to get an exact timeline for your job.
We order Schluter components through authorized supply sources and confirm the model against your assembly before anything is ordered, so you know what’s going in. Our techs have up to 28 years of experience, and the crew is background-checked. You’ll get a written line-item estimate before we start. Call (844) 560-4526 for a free estimate.
Barrett & Sons Construction Glendale pulls permits and signs inspections on every eligible job. You can look up our license number yourself before you sign anything. We also service KraftMaid, Cambria, and Silestone where your project touches those materials.
Call (844) 560-4526 for a free estimate. A written quote, no guesswork, no surprise invoices. We answer the phone around the clock, and we’re happy to give a free second opinion on any written estimate you already have.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.