Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Kitchen Remodeling: The Glendale Owner’s Guide
Schluter kitchen remodeling in Glendale runs $14,000 to $45,000 installed, with the waterproofing and tile-underlayment layer typically accounting for $1,200 to $4,000 of that figure. A smaller Glendale kitchen in that range often lands closer to $9,000 to $20,000. The most common failure we see isn’t the tile itself; it’s the Schluter membrane, curb, or drain flange beneath it letting go, which shows up as a soft grout line, a loose floor tile, or a darkened patch along the shower curb that never quite dries.
Owners usually discover it the slow way. A grout joint crumbles under a fingernail. A floor tile rocks when you step on it near the sink. Or the tile around a Schluter shower curb starts to lift at the corner, and once you press on it, water weeps out. That’s the moment the question shifts from “what’s wrong” to “which part do I actually need, and who is going to install it right.”
Key Takeaways
- Schluter failures in Glendale kitchens are almost always at the seams, corners, or drain flange, not in the field of the membrane.
- OEM Schluter parts are matched to specific series; the wrong flange or band will not seal correctly no matter how it’s installed.
- We’re an independent construction company, not affiliated with Schluter, and we don’t claim to stock parts or carry them on a truck.
- Every eligible job gets permits pulled and inspections signed, and every price change arrives as a written change order before work starts.
Which Schluter Models This Applies To
Schluter makes dozens of products that end up in a Glendale kitchen, and the part you need depends entirely on which line the original installation used. The main families are:
- KERDI and KERDI-BAND – the sheet waterproofing and seam banding used behind tile in wet areas. KERDI comes in 5-meter and 30-meter rolls and multiple widths; KERDI-BAND is the narrower seam tape that bridges corners and overlaps.
- KERDI-SHOWER and KERDI-LINE – prefabricated shower trays and linear drains. The drain flange and bonding flange are model-specific and not interchangeable between standard KERDI-DRAIN and the linear KERDI-LINE assemblies.
- DITRA and DITRA-HEAT – the uncoupling membrane under kitchen floor tile, and the version with integrated electric heating cable. DITRA-HEAT uses a specific cable spacing that has to match the mat, so a replacement mat and cable must come from the same product family.
- SCHIENE, JOLLY, and QUADEC – the edge profiles and trim pieces at tile transitions. These come in specific heights (measured in millimeters) that must match your tile thickness plus thinset.
To identify what you have, look for the printed Schluter branding along the edge of any exposed membrane or trim, and measure the tile thickness at the transition. The profile height has to match tile-plus-mortar, so a 10mm SCHIENE will sit proud on 8mm tile and a 12.5mm will not sit flush. That measurement matters more than the brand name on the box. We buy OEM Schluter parts for the repair because the seal geometry and bonding fleece are what make the system work; a generic membrane cut to fit rarely seals the same way at a corner, and corners are exactly where Glendale kitchens fail. We also install KraftMaid cabinetry, Cambria and Silestone counters on these jobs, so the waterproofing and the finish work are planned together, not bolted on after.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Kitchen Remodeling Is Failing
- Grout lines cracking at the shower curb or floor transition. This usually means the KERDI band at the seam has lost its bond, so the two surfaces are moving independently. Grout can’t bridge movement it wasn’t designed for.
- Hollow or “drummy” floor tile over what should be DITRA. Tap with a screwdriver handle; a dull thud instead of a sharp click means the tile has separated from the membrane or the membrane has separated from the subfloor. In Glendale homes with slab-on-grade kitchens, this often tracks back to moisture wicking up from below.
- A soft or darkened patch along the shower curb. Schluter curbs are foam or mortar cores wrapped in KERDI; if water gets behind the wrap at a corner, the core stays damp and the tile above it starts to loosen. This is the single most common failure we’re called out for.
- Lifting or curling at the Schluter edge profile. A SCHIENE or JOLLY that has pulled away usually means the thinset behind it failed, often because the profile was set over an uneven tile edge or the substrate wasn’t flat.
- A musty smell after a shower, even when the room looks clean. That’s trapped moisture behind the membrane, and it points to a breach somewhere you can’t see. It won’t resolve on its own.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Replacing a failed Schluter assembly in a Glendale kitchen or adjoining shower typically falls inside the $14,000 to $45,000 kitchen remodel range, and the waterproofing portion of that job is usually $1,200 to $4,000 depending on scope. Smaller kitchen repairs within that footprint run $9,000 to $20,000. Here’s what drives the number:
| Line item | Typical installed range |
|---|---|
| Schluter membrane and banding replacement (small area) | $800 – $2,500 |
| Shower curb / drain flange rebuild | $1,200 – $4,000 |
| Kitchen floor tile and DITRA re-set | $4,000 – $13,000 |
| Full kitchen remodel including waterproofing | $14,000 – $45,000 |
| Cabinet installation (KraftMaid) | $4,000 – $13,000 |
| Countertop installation (Cambria or Silestone) | $2,000 – $6,500 |
OEM Schluter parts cost more than generic equivalents, and we’ll tell you why we recommend them when we quote. Every price change comes to you as a written change order before a single nail moves. The work is backed by our written 90-Day Done Right Promise: if it’s not done right, Tom comes back and makes it right, one call.
DIY or Call Us?
There are safe checks you can do yourself. Tap the floor with a screwdriver handle to find hollow spots. Press a dry paper towel against the shower curb corner and see if it wicks moisture. Measure your tile thickness at an edge profile so you know what height you need. Those are fine.
What goes wrong when owners try the repair themselves is at the seams. KERDI requires a specific thinset (modified, and mixed to the right consistency), a minimum overlap at every joint, and full embedment of the band with no voids. One corner that isn’t fully bonded is how water gets in, and you won’t see it for months. The drain flange also has to be set at the correct slope and height relative to the tile plane; get it wrong and the shower pools. That’s not a scare tactic, it’s just where the skill lives. We pull permits and get inspections signed on eligible jobs, and the inspector signs off on work that’s actually correct.
Call (844) 560-4526 to schedule a free estimate. We’ll tell you straight whether you have a $1,200 repair or a full rebuild.
FAQs
How long does a Schluter waterproofing system last in a Glendale kitchen?
Fifteen to twenty-five years is typical when it’s installed correctly and the seams hold. The membrane itself is durable; what shortens its life is a missed overlap, a cut corner, or a drain flange set at the wrong height. Glendale’s dry summers don’t stress the product much, but the afternoon heat cycling through a kitchen with a west-facing wall can make minor seam failures show up faster.
Can I repair a failing Schluter seam instead of replacing everything?
Yes, often. A localized seam failure can be reopened, cleaned, and re-banded with fresh KERDI-BAND, and the tile above it reset. If the failure is limited to one corner, you’re usually looking at the lower end of that $800 to $2,500 range. If the core of a shower curb has stayed wet, that’s a rebuild. Call (844) 560-4526 and we’ll tell you which one you’re looking at.
How long does it take to swap a Schluter part?
A single seam re-band and tile reset is a one-day job once thinset cures out. A shower curb and drain flange rebuild runs three to five days because of cure times and inspection scheduling. We give you a written timeline up front, not a number shouted over the phone.
How do you source the Schluter part?
We order OEM parts matched to your specific series from a distributor, using the measurements and model numbers from your existing installation. We don’t claim to carry parts on a truck, and we won’t substitute a generic membrane on a Schluter job. If you need a part sourced or a whole kitchen waterproofed correctly, call (844) 560-4526 for a free estimate.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.