Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Owens Corning Kitchen Remodeling: The Glendale Owner’s Guide
If you’re pricing Owens Corning kitchen remodeling in Glendale, a full kitchen remodel typically runs $14,000 – $45,000 installed, and a small kitchen comes in at $9,000 – $20,000. Owens Corning doesn’t make the cabinets, counters, or doors themselves – it makes the insulation, underlayment, and moisture-resistant substrates that go behind and under those surfaces – so “Owens Corning kitchen remodeling” almost always means the hidden layer failed, not the pretty layer. Most Glendale owners find out the hard way: a soft spot under the sink that flexes when they step on it, a backsplash tile that pops loose in a straight line, or a musty smell after the first rain that won’t go away no matter how much they clean.
Which Owens Corning Models This Applies To
Owens Corning’s kitchen-relevant products fall into a few families: FOAMULAR extruded polystyrene rigid board (the common pink sheets used behind tile backer and under slab), the PINK fiberglass batts used in interior and exterior kitchen walls, and their moisture-resistant drywall and underlayment lines. Series names and thicknesses matter more than brand loyalty. FOAMULAR comes in 1/2″, 3/4″, 1″, 1.5″, and 2″ thicknesses, and the compressive strength rating (expressed as “25”, “40”, “60”, “100” PSI) is stamped on the face – the 40 PSI board is the one you want under a tile floor, not the 25. Fiberglass batts are labeled by R-value and width; a kitchen exterior wall in Glendale’s climate zone typically calls for R-13 to R-15 in a 2×4 cavity, R-19 to R-21 in a 2×6.
To match the right replacement, look for the printed label on the face of the board or the paper flange of the batt – the R-value, thickness, and PSI rating are all there. If the label is gone, a tape measure and a look at the cavity depth will tell you what was originally installed. On the OEM-versus-aftermarket question: for FOAMULAR and PINK fiberglass, brand-matched replacement is the correct call because the thickness, density, and vapor-permeance are tuned together. For underlayment and backer boards, a quality equivalent from a name you can verify (KraftMaid, Cambria, and Silestone are the surface brands we install in Glendale kitchens) is fine as long as the spec sheet matches. Knife-and-fork substitutions are where moisture problems start.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Owens Corning Kitchen Remodeling Is Failing
- Soft, spongy floor tile near the dishwasher or sink. The underlayment board has taken on water and lost its compressive strength – common when the original install used 25 PSI FOAMULAR under a tile floor instead of 40 PSI.
- Backsplash or counter tile lifting in a straight horizontal line. That’s not a tile problem, it’s a substrate problem – the backer or foam behind it has shifted or swelled, and the thinset let go along the seam.
- Musty smell in the kitchen after rain, strongest near exterior walls. Wet fiberglass batts lose their R-value fast and don’t dry out once the paper facing is soaked. Glendale’s hot, dry summers followed by winter rains create the perfect swing for moisture to get trapped and stay.
- Visible pink or blue foam crumbled or powdery behind an outlet or under a cabinet toe-kick. UV exposure or long-term water contact breaks down extruded polystyrene; once it’s chalky, it’s not insulating anything.
- Cold spots on the kitchen floor in winter over a slab or unheated crawlspace. Foam board under the floor was either never installed or was installed at the wrong thickness – the 1/2″ board used where 1″ was specified shows up as a chill you can feel through socks.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for the Owens Corning work depends on how much has to come out to get the new layer in. A full kitchen remodel that includes replacing failed substrate and insulation runs $14,000 – $45,000 in Glendale. If the failure is contained to one area – a backsplash, an island base, a floor section under the sink – the standalone line items apply: backsplash installation $800 – $2,500, kitchen island installation $3,000 – $10,000, cabinet installation $4,000 – $13,000, countertop installation $2,000 – $6,500. Small kitchens where the whole substrate is being refreshed run $9,000 – $20,000.
What drives the range: whether the failed layer is behind tile (tile has to come out to fix the substrate, then go back), whether a permit is required for any electrical or plumbing relocation inside the kitchen, and whether the moisture source was fixed or just covered up. Our quotes are line-itemed – materials, labor, and any allowance for tile or counters, all written down before we start. Every eligible job gets permits pulled and inspections signed. Every completed kitchen is covered by the written 90-Day Done Right Promise. Reach us at (844) 560-4526 for a free estimate.
DIY or Call Us?
What a homeowner can safely check: the printed label on the face of the foam board or batt to confirm R-value and PSI, the cavity depth, whether moisture is present (a cheap pin meter from the hardware store reads this in seconds), and whether the underlayment is soft underfoot. Those four checks take twenty minutes and tell you most of what a pro would learn on a first visit.
Where DIY goes wrong: pulling tile to chase a substrate without a plan for what’s under it, replacing fiberglass batts without addressing the water that soaked the old ones (you’ll be back inside that wall next winter), and reinstalling underlayment at the wrong thickness because the only board in stock at the store was the 1/2″ instead of the 1″. None of those are dangerous the way electrical or gas work is – the risk here is repeating the failure and paying twice. If the moisture source isn’t found and fixed first, no amount of new Owens Corning product will hold up. Call (844) 560-4526 and we’ll tell you honestly whether your situation is a Saturday project or a pro job.
FAQs
Twenty to forty years is typical for FOAMULAR under a protected floor and PINK batts in a dry wall cavity, but in Glendale’s climate the realistic lifespan depends on moisture control – once a batt or board gets soaked and stays wet through a winter, the useful life drops to a few seasons. If the source of moisture is fixed, the replacement will last. Call (844) 560-4526 for an exact quote – estimates are free.
Sometimes. A small section of foam board or a single batt can be patched if the surrounding product is still dry and sound; a full underlayment layer behind tile almost always needs replacement because the failure runs along seams and won’t hold a patch. We’ll tell you which one you’re looking at during the estimate. Call (844) 560-4526.
A contained backsplash or island-base replacement is typically one to three days; a full kitchen floor or wall substrate replacement with new tile runs five to ten working days depending on tile size and drying time. Small kitchens where the whole floor is being refreshed usually land in the one-to-two-week range. Call (844) 560-4526 for a schedule based on your specific kitchen.
We identify the product from the printed label or, if the label is gone, from the measured thickness, cavity depth, and PSI rating, then quote the correct FOAMULAR or PINK spec for that location. We don’t stock parts, and we don’t carry inventory on a truck – we source to the spec. Since we’re an independent contractor, not affiliated with Owens Corning, the recommendation is based on what your kitchen actually needs, not which product line is sitting around. Call (844) 560-4526 for a free estimate.
Barrett & Sons Construction Glendale is an independent remodeling contractor serving Glendale and the surrounding communities. We install Owens Corning-compatible substrate and insulation as part of full kitchen and bathroom remodels, along with KraftMaid, Cambria, and Silestone finishes. Every eligible job gets permits pulled and inspections signed, every price change arrives as a written change order before the work moves, and every completed job carries the 90-Day Done Right Promise. Call (844) 560-4526 for a free estimate – a live person answers, day or night.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.