Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Glendale Owner’s Guide
Barrett and Sons Construction installs CGI-compatible kitchen remodeling in Glendale, with full kitchen projects typically running $14,000 – $45,000 and cabinet installation alone at $4,000 – $13,000. We’re an independent contractor, not affiliated with CGI, and we pull the permits, write every allowance down, and pass inspection before we call a job done. Most Glendale owners find us after a door sags and won’t close, a drawer box cracks at the corner joint, or a finish starts peeling near the sink – small failures that point to a hinge, a box, or a door that’s reached the end of its run.
Key Takeaways
- CGI-compatible cabinet work in Glendale: $4,000 – $13,000 for installation, $14,000 – $45,000 for a full kitchen.
- Most hinge and drawer-box failures we see are a part swap, not a gut job.
- Particleboard swells where it gets wet – sink bases and dishwasher bays fail first.
- We measure your existing cabinets before we quote a replacement part.
Which CGI Models This Applies To
CGI cabinet and drawer systems show up across their stock and semi-custom lines, and the part you need depends less on the brand than on the hardware series inside the box. Before you order anything, open the door and look for a maker’s mark: a sticker on the cabinet box interior, a stamp on the hinge arm, or a printed label on the drawer side or bottom. Hinges are usually a European-style concealed cup hinge, and the cup diameter and screw-hole spacing are what matter – a 35mm cup with 45mm or 52mm spacing is common, but it isn’t universal. Drawer boxes are typically side-mount or undermount slides with a rated load, often 75 to 100 pounds on a full-extension slide. Measure the existing slide length and the box depth; if you order a slide an inch too long, it won’t clear the back of the cabinet.
On CGI cabinets specifically, the wood-grain and painted finishes are batch-sensitive, so a door or drawer face ordered later can read slightly different from the ones already installed. That’s a real compatibility gotcha in Glendale’s bright afternoon light. For hardware, a quality aftermarket hinge that matches the cup and spacing is fine and often cheaper than an exact factory part. For a door or drawer face, match the series and finish code, not just the color name. We carry KraftMaid, Cambria, and Silestone too, so if a mixed kitchen is what you’ve got, we can source the right piece for each.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Kitchen Remodeling Is Failing
- Doors that drift and won’t stay closed. The hinge tension screws back out over time, or the plastic cup cracks at the screw boss. A single door that suddenly swings open is usually the hinge, not a crooked cabinet.
- Drawer boxes splitting at the corners. Particleboard boxes pull apart at the dowel or staple joint where they carry weight. It happens faster in Glendale homes where a dishwasher vents moisture into the bay.
- Soft or swollen cabinet bottoms. A slow sink leak or a cabinet under a dishwasher wicks water into the board. Once particleboard swells, it doesn’t shrink back – the base needs replacing.
- Peeling or bubbling finish near the sink and range. Steam and splashes break down the finish at the edges. It’s cosmetic until the wood underneath takes on water.
- Slides that grind or stick under load. Worn rollers and bent slides cause drawers to hang. A drawer that only closes with a shove is telling you the slide or the box is worn.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Glendale, expect these installed ranges, part and labor together. We quote in writing, line by line, and a price change only happens with a signed change order before any work starts.
| Work | Installed Range (Glendale) |
|---|---|
| Cabinet installation (replacement doors, boxes, hardware) | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Full kitchen remodel | $14,000 – $45,000 |
What drives the range: how many doors and boxes are involved, whether the boxes need replacing or just hardware, the finish and series, and whether a countertop or backsplash comes off and goes back on. A single hardware swap sits at the bottom; a run of new cabinets with a resurfaced counter sits at the top. Every eligible job gets permits pulled and inspections signed, and the work is backed by our written 90-Day Done Right Promise – if something’s not right, Tom comes back and fixes it on one call.
DIY or Call Us?
You can safely tighten hinge screws, adjust a European hinge’s tension with a screwdriver, clear a slide track, and measure parts for an order. That part is fine to do yourself. Where it goes wrong: pulling a cabinet that’s screwed to the wall and possibly to a countertop or an electrical line behind it, or forcing a swollen particleboard box that splits and takes the finish with it. If you’re swapping a base cabinet under a sink, shut the water off and check for a live wire before you drill – and if you smell gas near the range, stop and call a professional. For a door, drawer, or hardware swap, call (844) 560-4526 and we’ll match the part and handle it.
FAQs
Quality hinges and slides run 10 to 15 years under daily use; in Glendale’s dry summers and warm inland afternoons, the finish on doors near a window can fade or check sooner. Cabinet boxes last decades if they stay dry, which is why sink-base leaks matter so much.
Often, yes. A drifting door usually just needs a hinge swap or tension adjustment, and a grinding drawer is usually a slide. A split drawer box or swollen particleboard base can’t be repaired safely – it needs a replacement. Call (844) 560-4526 and we’ll tell you which it is.
A single hinge or drawer slide is a short visit, often under an hour. A run of doors or a set of drawer boxes is usually a half day to a full day, depending on the count and whether the countertop or plumbing has to come off. We confirm the time in your written quote.
We start by identifying your cabinet series and hardware from maker’s marks, hinge cup measurements, and slide length, then match it before ordering. You’ll see the part and price on paper first. Call (844) 560-4526 for a free estimate and a written line-item quote.
If your CGI kitchen in Glendale has a door that won’t sit right, a drawer that grinds, or a base that’s swelled where it got wet, call Barrett and Sons Construction at (844) 560-4526 to schedule your free estimate. We’ll measure, match the part, and put the price in writing – and you’ll see the same crew on the return visit. Ask your neighbors or look up the license yourself; we’re twenty minutes away, so if something’s wrong, we want to know about it.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.