Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Roofing: The Glendale Owner’s Guide
If your ES Windows roof component has failed, we install compatible replacements across Glendale for $400 to $1,800 for a repair, or $8,000 to $20,000 for a full roof replacement, and most repairs are scheduled within a few days of your call. Owners usually figure it out after a ceiling stain on a Glendale hillside home, a shingle flap after a Santa Ana wind, or a roofer who taped off a “soft” flashing detail and never came back. ES Windows used a handful of trim and flashing profiles tied to its window-and-roof systems, so matching the right part matters more than grabbing the nearest thing off a shelf.
Which ES Windows Models This Applies To
ES Windows made windows, doors and the exterior trim and flashing assemblies that tie them into your roof and walls. The roofing-related parts that fail most are the flashing kits, drip-edge trim, skylight-to-roof seals, and the metal transition caps used where the ES Windows vinyl or aluminum frames meet shingles or tile. To identify the right part, look for the label on the inner jamb of your ES Windows unit: it carries the series code and, on many units, the model number. Write that code down before you call. If the label has peeled, measure the opening and the frame depth; ES Windows sizes ran in standard rough-opening dimensions, so the series can often be matched from the frame width and the trim profile.
OEM versus aftermarket is a real decision for ES Windows. The OEM flashing profile matched the frame pocket exactly, which cut down on re-caulking and silent leaks. Aftermarket kits in the correct aluminum gauge and profile work just as well when a trained installer sets them, and they’re often easier to find for older Glendale homes where the original ES Windows label is gone. What we won’t do is pressure you toward the more expensive option because “OEM only” sounds better. We’ll show you both and let you decide.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ES Windows Roofing Is Failing
Here are the symptoms we actually see in Glendale:
- Dark stains on the ceiling near an ES Windows skylight or vault seam. Usually a failed flashing gasket or cracked seal where the frame meets the roof deck, common in Glendale homes after a dry summer and a real rainy season.
- Wet trim or peeling paint around an ES Windows window head. Tells you the drip-edge trim or the roof-to-wall cap has lost its seal, and water is running back into the wall cavity.
- Shingle or tile lifted near the window edge. That’s usually wind, not the window itself, but the flashing under that edge is often cracked or missing.
- Soft or spongy drywall after rain. A slow leak from an ES Windows flashing detail, one that only shows after heavy rain, is often present for months before you see it.
- Visible daylight around a skylight frame. Either the seal plate has aged out or the roof deck has settled, and it needs a proper look, not another tube of caulk.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Glendale, a roofing repair tied to an ES Windows component runs $400 to $1,800. That covers inspection, matching the part, the compatible flashing or trim, labor, and a written 90-Day Done Right Promise on the work. A full roof replacement, if the ES Windows roofs around your home are past their service life, runs $8,000 to $20,000 and includes a written scope, all line items and allowances in writing, and permits pulled where the work requires them. Here’s what moves the range:
- How much roof is tied into the failed part – one flashed detail versus tearing back a whole plane.
- Shingle or tile accessibility – Glendale’s mix of tile and shingle roofs changes removal time.
- The part itself – OEM profile versus a matched aftermarket equivalent.
- Decking condition – any rot discovered under the flashing is a written change order before we touch it.
DIY or Call Us?
There’s real overlap between what you can safely check and what should be in the hands of a crew. You can inspect the label on your ES Windows unit, write down the series code, take photos of the area where water is coming in, and clean the gutters. What you should not do is climb onto a Glendale tile roof in the heat, pry up shingles, or try to reseal a skylight from the top – the fall risk and the chance of doing more damage than the original leak is high. Roof work at height is the part we’d genuinely rather you didn’t attempt, both for your safety and because a botched flashing detail can cost more to fix than the original repair.
Call (844) 560-4526 for a free second opinion on any written estimate, and we’ll be honest about whether you’re looking at a small repair or something bigger. No trip charge inside the county, and a live person answers the phone.
FAQs
Plan on 15 to 20 years for the flashing and metal trim when installed right, and five to eight years for the rubber gaskets and sealant around skylights and window heads. Glendale’s dry summers followed by real winter rain take a toll on any roof seal, so re-checking the caulked joints every few years is normal maintenance, not a sign of bad work.
Often yes. If the ES Windows component itself is failing and the rest of the roof is sound, a targeted repair is the right call, and in Glendale that runs $400 to $1,800. If you’ve got multiple leaks or the shingles are brittle, replacement is the better spend. Call (844) 560-4526 and we’ll tell you which one you’ve got.
Most single-component repairs are done in a few hours, and a skylight-to-roof re-seal is usually a single-day job. If it turns into a larger flashing rebuild or roof section replacement, plan on two to four days, weather permitting, and you’ll know that before we start.
We match the series code from your ES Windows label to the correct profile, then source from distributors who actually stock the size we need. If OEM isn’t available, we offer the aftermarket equivalent in the right gauge and show you the difference. Barrett & Sons Construction Glendale is an independent service provider and isn’t affiliated with ES Windows – we also carry KraftMaid, Cambria and Silestone for other parts of your project. Call (844) 560-4526 for a free estimate.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.