Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Ameristar Fence Installation: The Glendale Owner’s Guide
Ameristar aluminum fence installation in Glendale, CA typically runs $3500 – $9000 for a standard residential run, depending on linear footage, panel height, grade changes and gate count. We install Ameristar-compatible aluminum fencing across Glendale and surrounding neighborhoods, and we handle the parts matching, layout and permitting while you get a written line-item quote before anything gets dug. If a panel, post or gate section has already failed, we’ll price the repair and the replacement side by side.
Most Glendale owners find out something’s wrong the same way. The gate starts dragging on the latch strike. A post at the driveway apron looks a little off-plumb. Then a wind event comes through the Verdugo foothills and a whole panel section leans. Aluminum fencing is unforgiving that way: it fails at the connections first, not the finish. The powder coat looks perfect right up until the footings tell the story.
Which Ameristar Models This Applies To
Ameristar’s residential lines split mostly by picket style and rail profile – the classic three-rail ornamental look, the flat-top and spear-top variants, and the welded panel systems used for pool code and commercial-grade runs. The part that fails, in almost every case, is not the panel. It’s the post footing, the post itself at the ground line, the hinge and latch hardware on the gate, or the bracket that ties panel to post.
To identify what you’re working with, measure your post spacing center to center. Standard Ameristar residential panels run on 6-foot or 8-foot spacing, but Glendale’s sloped lots frequently use racked panels and stepped transitions, so the spacing on your run may not be uniform – especially along driveways that climb toward Chevy Chase Canyon. Measure the post section too. Ameristar’s posts come in different wall thicknesses, and matching the right one matters if you’re replacing a single post rather than a run. Look for the manufacturer label on the inside of a rail or on the gate frame; it usually lists the series. If there’s no label, take three measurements (post spacing, post size, panel height) and we can match it from there.
On the OEM-versus-aftermarket question: Ameristar’s own posts and brackets are the cleanest match, and for a partial replacement we lean that way. For hardware and footings, quality aftermarket equivalents are fine and often what we’d specify anyway, because the post base and concrete footing are doing the structural work regardless of whose name is stamped on the bracket. We don’t claim to stock parts or carry them on the truck – we source what your specific run needs, and we tell you which is OEM and which isn’t in the quote.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Ameristar Fence Installation Is Failing
- Post bases leaning after wind or soil movement. In Glendale, the shrink-swell clay soils in some foothill areas and the older alluvial ground closer to the flats both move seasonally. A post set too shallow or in a footing that’s cracked will lean before the panel ever bends.
- Rust bleeding at the ground line on the post. Powder-coated aluminum doesn’t rust, so if you’re seeing corrosion it’s almost always a steel post or a steel bracket that’s been wicking moisture. That’s a footing drainage problem as much as a parts problem.
- Gate sag at the hinge side. Aluminum gates are light but they’re long, and a hinge plate that’s loosened in the post wall or a post that’s shifted a quarter inch will drop the latch out of alignment. If the gate drags, don’t shim the latch – find the cause.
- Loose or missing panel-to-post brackets. These are small stamped pieces and they take the wind load. A missing bracket on a run facing the Santa Ana wind corridor is a panel waiting to peel.
- Powder coat chalking or chipping at cut edges and welds. Sun exposure across Glendale is hard on finishes. Chalking is cosmetic; chipping that exposes bare aluminum at a weld is where you’ll eventually get pitting.
Replacement Cost & What’s Included
Full Ameristar-compatible aluminum fence installation in Glendale runs $3500 – $9000 for a typical residential property. That’s the installed number: materials, footings, layout, and cleanup. The lead driver is linear footage, followed by grade difficulty, gate count and whether we’re tying into an existing run or starting fresh.
For a partial replacement – a post section, a gate, a few panels – the price is quoted line by line so you can see parts and labor separately. What drives the range on a repair:
- Number of posts being reset or replaced
- Footing depth required and whether old concrete has to come out
- Whether the panels are racked for slope and need to be re-cut to fit
- Gate hardware (hinges, latch, self-closer if pool code applies)
- Whether a permit is required – Glendale has fence height and setback rules that vary by zoning, and we pull the permit when the job is eligible for one
Every price change gets a written change order before work proceeds. Not after. Every completed job is covered by our written 90-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Here’s the honest split. You can safely check your own fence, and you should. Walk the run, push each post, look at the ground line for cracks or settling, open and close the gate, and check whether the brackets are all there. Take photos and measure your post spacing. That five minutes will tell you whether you have a hardware problem or a footing problem, and we’ll take those photos over the phone and tell you what we see.
What we would not do yourself: resetting a post in concrete, or re-hanging a gate that’s structurally loaded. A leaning post that’s still under tension can come out hard and fast, and a gate frame is heavier than it looks. This isn’t a scare tactic – it’s just a job where a bad afternoon is more likely than a good result. We’re an independent contractor and not affiliated with Ameristar, so we can tell you plainly when an Ameristar-compatible repair makes more sense than a full replacement. Call (844) 560-4526 and we’ll talk it through.
FAQs
Expect 20 to 30 years on the aluminum itself when the powder coat is intact and the footings are sound. The real lifespan variable in Glendale is the footings, not the metal. Our technicians have up to 28 years of experience and we can tell you in about five minutes on-site whether your footings are holding. Call (844) 560-4526 for a free estimate.
Often, yes – a single post, gate or bracket set can usually be repaired without touching the whole run. Whether repair makes sense depends on how much of the run shares the same footing problem. If it’s one post, we repair it. If it’s four posts on the same soil line, we’ll show you the math on replacement. Call (844) 560-4526 and we’ll price both.
A single post or gate section is typically a half-day to a full day, and a full run depends on footage and footing cure time. Concrete needs time, so we don’t rush that step. Call (844) 560-4526 and we’ll give you a realistic schedule, not an optimistic one.
We match it to your specific model or measurement before ordering, and we tell you in writing whether it’s OEM or a quality aftermarket equivalent. We don’t claim to keep parts on hand. Calls are answered by a live person 24/7, so you’re never leaving a voicemail about a part. We also install KraftMaid, Cambria and Silestone on interior jobs, if you’re already planning a bigger project. Call (844) 560-4526 for a free estimate.
Get a Written Quote on Your Ameristar Fence
Barrett & Sons Construction Glendale has been owner-operated since 1998, and every scope, allowance and price change arrives in writing before a single nail moves. If you’re dealing with a failed Ameristar section in Glendale, we’ll come out, look at the footings, and give you a written quote with the parts and labor broken out. Free second opinion on any written estimate you already have. No trip charge inside the county. The permanent 10% Senior & Veteran discount applies.
Call (844) 560-4526 to schedule your free estimate. A live person answers, day or night.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.