A Barrett company - serving Glendale, CA

Blanco Kitchen Remodeling in Glendale, CA

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Blanco Kitchen Remodeling: The Glendale Owner’s Guide

Blanco doesn’t make a part called “kitchen remodeling” – they make the sinks and faucets that sit at the center of one, and when those parts fail, the fix is either a targeted replacement or a full remodel depending on what’s underneath. A full kitchen remodel in Glendale runs $14,000 – $45,000. A focused flank fix – a new Blanco sink and faucet paired into sound cabinets – typically lands at the low end of that range with a few days of work, not weeks.

Call (844) 560-4526

Glendale owners usually find the failure the way everyone does: a drip under the cabinet that starts staining the false bottom, or a Silgranit sink that’s chipped at the drain flange and backing up every time the disposal runs. On pre-1970 homes in the 91201 and 91203 ZIPs, we often find the real problem isn’t the Blanco fixture at all – it’s the 1960s galvanized drain stub that finally gave out behind it, and a kitchen remodel is the honest time to address both at once. We pull permits, we put every scope change in writing, and the 90-Day Done Right Promise is printed on the contract, not the brochure.

Which Blanco Models This Applies To

Blanco’s fixture lineup runs across a few distinct families, and the part you need depends on which one you own. The Silgranit sink series (Diamond, Precis, Valea, Liven) is the most common in Glendale kitchens – a granite composite material that takes chips and heat stress differently than stainless, and the drain flange, mounting clips, and strainer assemblies are model-specific. The IKON apron-front line uses a different undermount clip kit than the drop-in Diamonds. Faucet lines like the Empressa, Sonoma, and Culinary use different cartridge part numbers even when the spouts look similar on a shelf.

To identify your exact fixture, look for the model sticker on the underside of the sink rim or the base of the faucet body – it’s usually a small foil label with a six- to eight-character model code. If the sticker is gone, measure the sink’s outside length and width in inches and note the bowl depth; Blanco’s spec sheets are public and match on those three numbers. For faucets, count the handle configuration and measure the spout reach. Bring a photo of the underside, not just the top.

On the OEM-versus-aftermarket question, Blanco-specific parts (cartridges, mounting hardware, drain fittings) are worth sourcing genuine when the fixture is under 10 years old – the tolerances on the composite sink drain flange in particular don’t forgive a universal part. Aftermarket baskets and strainers are fine. We aren’t affiliated with Blanco; we’re an independent Glendale service provider who has installed enough of these to know what fits.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Blanco Kitchen Remodeling Is Failing

  • Chipping at the drain or rim on a Silgranit sink. That’s impact or thermal shock, not a defect – composite chips when a cast-iron pan lands wrong or boiling water hits cold stone. A chip at the flange is the failure point because water gets behind the seal.
  • Persistent drip from the faucet base. Almost always a worn cartridge or O-ring. On a Blanco pull-down, the cartridge wears faster in Glendale’s hard water – mineral scale builds in the mixing chamber and the seal fails from the inside.
  • Water stains on the cabinet floor beneath the sink. This is the drain assembly or the tailpiece connection, and it’s the symptom that does the most hidden damage. By the time the stain shows, the particleboard cabinet base has been swelling for weeks.
  • Loose or rusted undermount clips. Blanco undermount sinks use bracket clips that loosen over time – once they do, the sink drops a fraction of an inch and the silicone seal breaks. That’s a leaking sink and a failing cabinet in the same motion.
  • Disposal vibration loosening the drain connection. Not a Blanco failure per se, but a common cause of sink leaks when the disposal’s mounting ring wasn’t torqued to spec against a composite sink – which is softer than stainless and needs a different tightening sequence.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For Glendale, here’s what kitchen work tied to Blanco fixtures actually runs:

Scope Installed Range
Full kitchen remodel (cabinets, counters, sink, faucet) $14,000 – $45,000
Small kitchen remodel (galley or condo kitchen) $9,000 – $20,000
Cabinet installation (Blanco sink base included) $4,000 – $13,000
Countertop installation with sink cutout $2,000 – $6,500
Backsplash installation $800 – $2,500
Kitchen island installation $3,000 – $10,000

What drives the number in Glendale: whether the sink base cabinet has to be replaced (water damage from a slow leak often forces it), whether the countertop is Cambria quartz or laminate, and whether the plumbing stub-outs need updating. We write the parts and labor separately on the estimate. If the scope changes mid-job – and under a Blanco composite sink, it sometimes does once we open the cabinet – the change order comes in writing before we touch anything. 90-Day Done Right Promise on the finished work.

DIY or Call Us?

You can safely check a few things yourself: look under the sink with a flashlight for staining, run the faucet and watch the drain connection, and check the mounting clips for looseness. Tightening a loose clip with a screwdriver is fair game. Replacing a cartridge or dropping a new Blanco sink into an existing cutout is a different story – the mechanical part usually goes fine, but the seal, the cutout tolerance on a composite sink, and the disposal reconnection are where DIY leaks start. And on Glendale homes with older plumbing, we’ve seen homeowners accidentally torque a drain fitting and crack the cast-iron stub behind the wall – a $40 repair becomes a $1,200 one.

If you’re in a 91205 or 91206 home built before 1975, call us before you pull the sink. There’s often something in the drain line that’s worth seeing before the countertop comes off. Call (844) 560-4526 – a live person answers, and the estimate is free.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 560-4526
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Barrett & Sons Construction Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch