Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Home Additions & ADU: The Glendale Owner’s Guide
We build home additions and ADUs at CGI-compatible specs for Glendale homeowners, and projects here typically run $45,000 – $130,000 for an addition or garage conversion and $90,000 – $220,000 for a new ADU. The “part” in this case is the whole scope: foundation, framing, envelope, and finish. A 400-square-foot addition takes about four to six months from permit to final inspection; a detached ADU in Glendale usually runs nine to fourteen months because of plan check, Historic Preservation review in some zones, and utility coordination with Glendale Water & Power. Homeowners usually find out something has failed when a finished room starts feeling wrong: a door that won’t latch, a crack above a header, or a roof tie-in that leaks at the first real rain.
To be clear up front: Barrett & Sons Construction Glendale is an independent builder, not affiliated with CGI or any manufacturer. We’re the crew you call when the existing work needs to be brought to spec or corrected.
Key Takeaways
- Glendale additions run $45,000 – $130,000 installed; detached ADUs $90,000 – $220,000.
- Every eligible job gets permits pulled and inspections signed, including the handful of Glendale properties inside designated historic districts.
- Change orders are written before work moves, so the scope you priced is the scope you get.
- Our crew members have up to 28 years of experience, and every completed job is backed by our written 90-Day Done Right Promise.
Which CGI Models This Applies To
CGI’s modular and panelized lines aren’t branded the way a water heater is, so “which model” usually means matching the structural and envelope system your plans specify. The relevant identifiers:
- Panel module series. CGI structural insulated panels and pre-framed wall sections are ordered by span rating and R-value. Identify yours from the stamped label on the panel edge or the plan sheet’s structural notes. A 4-inch panel is not interchangeable with a 6-inch panel for a load-bearing wall, and mixing them mid-wall is how you get a deflection problem six months in.
- Tie and connector grade. Simpson Strong-Tie hardware specified at plan check (HDU or MST straps at the roof-to-wall connection, for example) has a specific stamp. Glendale sits in a seismic zone where the inspector will check the stamp, not just the presence of a strap.
- Window and door series. If your plans call for Andersen or Marvin units, the rough opening dimensions are series-specific. A 400 Series frame won’t drop into a rough opening framed for a different series without rework.
- Roof tie-in profile. Matching a GAF or CertainTeed shingle course to an existing roof means matching the underlayment spec, not just the color.
On OEM versus equivalent: for structural connectors and panels, stick with the stamped, listed product the plans name. The dollar savings on a substitute connector is $40 – $90 and the potential cost of a failed inspection is a week of framing. For finish trim and interior hardware, a quality equivalent is fine as long as you write it into the scope first. For CGI-specific hardware where you’re unsure what’s compatible, send us the label photo and the plan sheet; a free second opinion on any written estimate is a standing offer.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Home Additions & ADU Is Failing
These are the symptoms we see most on add-on and ADU work in Glendale. Each one has a specific cause, and the cause matters more than the symptom.
- Doors that won’t latch and drywall cracks above headers. Usually a foundation or framing issue, or a load path that wasn’t carried to the footing. In homes built on the older, shallow post-and-pier foundations common in parts of Glendale, this shows up faster than in slabs.
- Water staining at the roof tie-in. The most common failure point on an addition. It’s nearly always flashing detail at the valley where the new roof meets the old, not the shingle itself. Glendale’s winter rain volume exposes it in the first season.
- Warm or cool spots that don’t match the rest of the house. A panelized wall with a gap at the top plate, or an envelope that wasn’t sealed at the transition to the original structure.
- Condensation on interior walls near the addition. Insulation isn’t continuous across the old-to-new junction, so warm interior air hits a cold surface. Fix the thermal break, not the wall finish.
- Pest access at the sill or bottom plate. An unsealed envelope joint. Common in Glendale homes backing onto hillside open space where drywood termites and roof rats move in.
If any of these show up before a final inspection, call us before covering anything up. Once drywall goes on, diagnosis cost triples.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in the Glendale market, with permits and inspections included on every eligible job:
| Scope | Typical Installed Range |
|---|---|
| Attached home addition | $45,000 – $130,000 |
| Detached ADU (new build) | $90,000 – $220,000 |
| Garage conversion to living space | $30,000 – $80,000 |
What drives the number: square footage, foundation type (slab versus raised), whether the roof tie-in is a simple gable or a valley, and the plans check timeline. Historic Preservation review in the Glendale districts that require it adds months, not dollars, but a redesign after a denial costs both.
We quote in line-item form. Allowances go on paper, and any scope change gets a written change order before a nail moves. Every price change is in writing, because an allowance that isn’t on paper is a surprise waiting for a date. Every completed job is covered by our written 90-Day Done Right Promise; if something’s not right, one call brings the crew back.
No surprise invoices at the end. That’s the whole point.
DIY or Call Us?
An owner can safely check a few things: photograph any crack, watch for door swing that shifts seasonally (a mark with a pencil on the frame tells you in a week), and check the roof tie-in from the ground with binoculars after a hard rain.
Structural work is a different animal. Cutting a header, reworking a load path, moving a footing, or chasing a roof leak down through flashing requires a permit and a licensed crew. Running a new circuit from the panel to a subpanel, if the addition needs one, means working inside a live panel, which is a task for a licensed electrician. The permit inspector works for you, not for us; that’s why Glendale homeowners should want the inspection done, not skipped. The last crew that told you permits were optional is exactly the reason to insist on them now.
If your project has been quoted, or you’ve been handed a written estimate you’re not sure about, call (844) 560-4526. That free second opinion is standing, not a promotion. Our crew members have up to 28 years’ experience, are background-checked, and the phone is answered by a live person around the clock. Ask anyone on your street, or look up the details before you sign anything.
FAQs
Built and sealed correctly, the framing and envelope should outlive the mortgage: 50-plus years for the structure, 20 to 30 years for the roofing and window systems, 8 to 15 for exterior sealants and caulk joints that need periodic renewal. Glendale’s sun exposure on south- and west-facing walls ages sealants faster than the coastal climate does, so inspect the envelope sealant every few years.
Call (844) 560-4526 for an exact inspection quote; estimates are free.
Often, yes. Cracks above headers, roof tie-in leaks, and envelope sealing problems are commonly addressed with targeted structural reinforcement, flashing rework, and re-sealing rather than a full rebuild. The decision rides on whether the load path and foundation are sound; a structural engineer’s report tells you which way to go before you spend anything.
Call (844) 560-4526 for a free second opinion on any written estimate.
The scope, not a part swap, is what we’re quoting here. A garage conversion runs two to four months; an attached addition, four to six months; a detached ADU, nine to fourteen months, with Glendale plan check and utility coordination as the variable. We give you a written schedule with the estimate, not a phone number and a shrug.
Call (844) 560-4526 to schedule your free estimate.
From the plan sheet and the stamped labels on your panels, ties, and window units, matched to the manufacturer’s current spec sheet. We buy the listed structural hardware the plans name, and we write the finish choices into the scope. No mystery brands from an unmarked truck.
Call (844) 560-4526 for an exact quote; estimates are free.
Barrett & Sons Construction Glendale pulls permits, signs inspections, and hands you a line-item quote with written change orders. The 90-Day Done Right Promise is written on every contract. If we worked on your home and something’s off, one call brings the crew back to make it right. Call (844) 560-4526 to schedule your free estimate. We also work with KraftMaid, Cambria, and Silestone on the finish side of these projects when your scope calls for them.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.