A Barrett company - serving Glendale, CA

CGI Kitchen Remodeling in Glendale, CA

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

CGI Kitchen Remodeling: The Glendale Owner’s Guide

Barrett and Sons Construction installs CGI-compatible kitchen remodeling in Glendale, with full kitchen projects typically running $14,000 – $45,000 and cabinet installation alone at $4,000 – $13,000. We’re an independent contractor, not affiliated with CGI, and we pull the permits, write every allowance down, and pass inspection before we call a job done. Most Glendale owners find us after a door sags and won’t close, a drawer box cracks at the corner joint, or a finish starts peeling near the sink – small failures that point to a hinge, a box, or a door that’s reached the end of its run.

Call (844) 560-4526

Key Takeaways

  • CGI-compatible cabinet work in Glendale: $4,000 – $13,000 for installation, $14,000 – $45,000 for a full kitchen.
  • Most hinge and drawer-box failures we see are a part swap, not a gut job.
  • Particleboard swells where it gets wet – sink bases and dishwasher bays fail first.
  • We measure your existing cabinets before we quote a replacement part.

Which CGI Models This Applies To

CGI cabinet and drawer systems show up across their stock and semi-custom lines, and the part you need depends less on the brand than on the hardware series inside the box. Before you order anything, open the door and look for a maker’s mark: a sticker on the cabinet box interior, a stamp on the hinge arm, or a printed label on the drawer side or bottom. Hinges are usually a European-style concealed cup hinge, and the cup diameter and screw-hole spacing are what matter – a 35mm cup with 45mm or 52mm spacing is common, but it isn’t universal. Drawer boxes are typically side-mount or undermount slides with a rated load, often 75 to 100 pounds on a full-extension slide. Measure the existing slide length and the box depth; if you order a slide an inch too long, it won’t clear the back of the cabinet.

On CGI cabinets specifically, the wood-grain and painted finishes are batch-sensitive, so a door or drawer face ordered later can read slightly different from the ones already installed. That’s a real compatibility gotcha in Glendale’s bright afternoon light. For hardware, a quality aftermarket hinge that matches the cup and spacing is fine and often cheaper than an exact factory part. For a door or drawer face, match the series and finish code, not just the color name. We carry KraftMaid, Cambria, and Silestone too, so if a mixed kitchen is what you’ve got, we can source the right piece for each.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your CGI Kitchen Remodeling Is Failing

  • Doors that drift and won’t stay closed. The hinge tension screws back out over time, or the plastic cup cracks at the screw boss. A single door that suddenly swings open is usually the hinge, not a crooked cabinet.
  • Drawer boxes splitting at the corners. Particleboard boxes pull apart at the dowel or staple joint where they carry weight. It happens faster in Glendale homes where a dishwasher vents moisture into the bay.
  • Soft or swollen cabinet bottoms. A slow sink leak or a cabinet under a dishwasher wicks water into the board. Once particleboard swells, it doesn’t shrink back – the base needs replacing.
  • Peeling or bubbling finish near the sink and range. Steam and splashes break down the finish at the edges. It’s cosmetic until the wood underneath takes on water.
  • Slides that grind or stick under load. Worn rollers and bent slides cause drawers to hang. A drawer that only closes with a shove is telling you the slide or the box is worn.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

In Glendale, expect these installed ranges, part and labor together. We quote in writing, line by line, and a price change only happens with a signed change order before any work starts.

Work Installed Range (Glendale)
Cabinet installation (replacement doors, boxes, hardware) $4,000 – $13,000
Countertop installation $2,000 – $6,500
Backsplash installation $800 – $2,500
Kitchen island installation $3,000 – $10,000
Small kitchen remodel $9,000 – $20,000
Full kitchen remodel $14,000 – $45,000

What drives the range: how many doors and boxes are involved, whether the boxes need replacing or just hardware, the finish and series, and whether a countertop or backsplash comes off and goes back on. A single hardware swap sits at the bottom; a run of new cabinets with a resurfaced counter sits at the top. Every eligible job gets permits pulled and inspections signed, and the work is backed by our written 90-Day Done Right Promise – if something’s not right, Tom comes back and fixes it on one call.

DIY or Call Us?

You can safely tighten hinge screws, adjust a European hinge’s tension with a screwdriver, clear a slide track, and measure parts for an order. That part is fine to do yourself. Where it goes wrong: pulling a cabinet that’s screwed to the wall and possibly to a countertop or an electrical line behind it, or forcing a swollen particleboard box that splits and takes the finish with it. If you’re swapping a base cabinet under a sink, shut the water off and check for a live wire before you drill – and if you smell gas near the range, stop and call a professional. For a door, drawer, or hardware swap, call (844) 560-4526 and we’ll match the part and handle it.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 560-4526
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Barrett & Sons Construction Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch