Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Kitchen Remodeling: The Glendale Owner’s Guide
Jerith-compatible kitchen remodeling in Glendale runs $14,000 to $45,000 installed, depending on whether you’re replacing a single failing component or rebuilding the whole room around it. Most Glendale owners we meet with a failed Jerith part aren’t sure what they’re looking at. They just know the cabinet line is off, a drawer stopped closing flush, or a panel that used to sit tight now grows a gap in the middle of the dry season.
We’re Barrett & Sons Construction Glendale, and we are an independent remodeling company. We’re not affiliated with Jerith, and we don’t claim to be. What we do is figure out which Jerith series you actually have, source the right replacement part or the right combination of cabinet, counter and finish components that matches it, and install it so the kitchen closes, lines up and holds up through a Glendale summer. Tom Barrett and his sons have been on the tools in this area for a long time, and our technicians bring up to 28 years of experience to a job like this.
The most common call we get from a Glendale homeowner sounds like this: “The kitchen was fine for years, then one drawer started sticking and now two more are doing it.” That’s usually how it starts. One part. Then a pattern.
Which Jerith Models This Applies To
Before we quote anything, we need to match your kitchen to the right Jerith line. Jerith’s product families don’t use the same drawer glides, hinge styles or cabinet mounting specs across the range, and a part that fits one series won’t fit another even when it looks similar from the outside. Here’s how we sort it out.
- Find the label or stamp. Jerith cabinet and millwork pieces usually carry a label inside the cabinet box, on the back panel, or on the inside of a door. Photograph it before anything else. Model numbers and series names change slightly over the years, so a clean photo of the label is worth more than a receipt.
- Measure the opening, not the part. Cabinet openings and drawer box widths are what actually determine fit. Measure the inside dimension of the cabinet carcass and the depth of the drawer box, and write those numbers down before you call us.
- Note the hardware style. Side-mount vs. undermount drawer glides, full-extension vs. standard extension, face-frame vs. frameless cabinets. This is the compatibility gotcha that trips most homeowners: a drawer box spec’d for side-mount glides will not accept an undermount slide without a box modification, even if the width is right.
- Check the finish year. Jerith finishes age differently depending on the wood species and the stain. A 2010 white oak door won’t match a 2022 white oak door exactly. We pull finish samples where we can, or we plan to replace the door plus its neighbor so the match is invisible.
The OEM-versus-aftermarket question matters here. For anything that carries weight and hinges or slides daily, we’d rather install a quality aftermarket glide or hinge that’s rated for the load than chase a discontinued OEM part that’s sat in a warehouse for a decade. For visible cabinet faces, doors, and trim panels, OEM is usually the only way to get a finish match. That’s a real decision, and it should be made before we order anything.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Jerith Kitchen Remodeling Is Failing
These are the five symptoms Glendale homeowners report most often. Each one points at a different underlying cause, and each one has a fix at a different price tier.
- A drawer that sticks or won’t close flush. Usually a worn drawer glide, a warped drawer box, or a cabinet carcass that’s shifted on its mount. The glide is the cheap fix. A shifted carcass is not.
- A door that sags or rubs the frame. Hinge wear, or hinge screws that have pulled out of soft wood. If the hinge itself is fine but the screw holes are stripped, the repair is a plug-and-rebuild, not a new hinge.
- Gaps opening between cabinet panels or at the wall line. In Glendale’s dry inland summers, wood shrinks. This is where low humidity in the San Fernando Valley and the Verdugo foothills does real damage over time, especially on kitchens with a south-facing window. A gap that opens in July and closes in January usually isn’t a defect, it’s seasonal movement, and it’s often solved with a proper scribe or filler strip rather than a replacement.
- Delamination or lifting finish on cabinet faces. Moisture intrusion behind the finish, usually near a sink or under a dishwasher. If the substrate has swelled, the part has to come out.
- A cabinet that’s pulling away from the wall. Anchor failure. This is the one that gets serious. If a wall cabinet is pulling out, stop loading it and stop using it. The fix is a re-anchor into studs, and it’s not something to leave until next spring.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest pricing picture for Glendale. These are installed ranges, not catalog prices, and they include the part, the labor, and hauling the old part away.
| Scope | Installed Range |
|---|---|
| Cabinet installation (full run) | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Full kitchen remodel | $14,000 – $45,000 |
What moves you up the range: the number of cabinet boxes, the finish matching work, whether the counter comes out with the cabinets, and whether the plumbing or electrical has to move. What moves you down the range: replacing components instead of the whole run, and staying with the existing cabinet layout. Our early conversations with you will include KraftMaid, Cambria and Silestone as comparison options if you’re rebuilding the counter and cabinet run at the same time. We’ll price those against the Jerith match so you can see the trade-off.
Every scope detail, every allowance, and every price change goes to you in writing before we order or install anything. No surprise invoice at the end. And the work is backed by our 90-Day Done Right Promise. If it’s not done right, one call brings Tom back.
DIY or Call Us?
There’s some of this work an owner can safely do themselves, and there’s some they can’t. Here’s the honest split.
Safe to check yourself: photographing the Jerith label, measuring cabinet and drawer openings, tightening a visibly loose hinge screw, and wiping down a delaminated panel to see how deep the swelling goes. Those four things are diagnostic, not structural. They’ll help us quote you accurately.
Not safe to do yourself: wall cabinets that are pulling away from the wall, any cabinet that has gas piping or electrical running through it, and any job that involves moving plumbing or a range hood duct. A wall cabinet that comes down while it’s loaded is a genuine injury risk. A cabinet that shares a cavity with a gas line is not a cabinet job, it’s a two-trade job, and it needs a licensed electrician or plumber on the crew. We pull permits whenever the job calls for them, and the permit inspector works for you, not for us. That’s why we like him.
If you’re not sure where your job lands, call us at (844) 560-4526. We answer the phone live.
FAQs
A quality cabinet glide or hinge in a Glendale kitchen typically lasts 12 to 20 years in daily use. Humidity swings in the San Fernando Valley and the Verdugo foothills shorten that on cabinets near a window or sink. When one part goes, check its neighbors.
Sometimes, yes. A hinge that’s lost a screw can be plugged and re-anchored. A drawer glide that’s rattling can often be swapped on its own. But a delaminated cabinet face or a carcass that’s pulled off the wall can’t be repaired to last. We’ll tell you which one you have before any work starts.
A single drawer glide or hinge replacement is usually a short visit. A cabinet run or a full kitchen remodel in Glendale is a multi-day to multi-week job depending on scope. We’ll give you the schedule in writing before we start.
We match the label and measurements from your kitchen first, then confirm the part number against the right Jerith series. We don’t stock parts and we don’t carry them on a truck, so every part for your job is ordered to spec. That’s why the label photo matters so much.
Yes, on every eligible job. Permits pulled, inspections signed, and a written change order for any price change before work proceeds. We also offer a free second opinion on any written estimate, a no-trip charge inside the county, $40 off any repair over $200, and a permanent 10% Senior & Veteran discount.
Give us a call at (844) 560-4526 to schedule your free estimate. We’ll look at the part, match it to your Jerith kitchen, and put the scope and price in writing before anything gets ordered. A live person answers 24/7. Barrett & Sons Construction Glendale is an independent remodeling company, not affiliated with Jerith. KraftMaid, Cambria and Silestone are also available to compare if your job grows past a single part.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.