Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Kohler Home Additions & ADU: The Glendale Owner’s Guide
Kohler fixtures and finishes for a home addition or ADU in Glendale, CA typically run $45,000 – $130,000 installed for an addition, $90,000 – $220,000 for a full ADU, and $30,000 – $80,000 for a garage conversion, depending on square footage, foundation work, and how much of the Kohler bath and kitchen package you carry through. We’re an independent construction company, not affiliated with Kohler, and we build to the spec sheet Kohler publishes for each fixture line.
Most Glendale owners don’t call us about a “failed part” on an addition. They call because a Kohler faucet cartridge in the new ADU bath started dripping within a year, or a Kohler shower valve trim they ordered won’t seat against the rough-in their plumber set. The part is usually the symptom. The install is usually the story.
Key Takeaways
- Kohler bath and kitchen fixtures are spec-driven: the rough-in valve, the trim, and the cartridge have to match as a set, and that’s where most Glendale failures start.
- An addition in Glendale runs $45,000 – $130,000; an ADU $90,000 – $220,000; a garage conversion $30,000 – $80,000.
- Permits get pulled and inspections signed on every eligible job. Glendale’s building department reviews ADUs closely, and a plan that skips that step is a problem you inherit later.
- Every price change arrives as a written change order before work moves. No surprise invoices at the end.
Which Kohler Models This Applies To
This applies across Kohler’s residential bath and kitchen lines, not one model. On the bath side that’s the Memoirs and Devonshire collections, the Purist and Artifacts trim families, and the Rite-Temp and Pressure-Balancing rough-in valves that sit behind most of them. On the kitchen side it’s the faucet lines that use Kohler’s ceramic disc cartridges, plus the undermount and farmhouse sink specs that drive cabinet cutout dimensions in a new build.
Here’s the compatibility gotcha that trips up Glendale ADU owners: Kohler’s rough-in valves are not interchangeable across trim families. A Memoirs trim will not seat on a Rite-Temp rough-in, even though both are Kohler and both look right in the box. The rough-in goes in during framing. The trim gets picked later. If those two decisions happen months apart and nobody checks the part numbers, you’re buying a valve twice. Pull the label off the inside of the valve body or the trim escutcheon and match the model number on Kohler’s spec sheet before you order anything.
On the OEM-versus-aftermarket call: for cartridges and seals, we stay with Kohler OEM. Aftermarket ceramic cartridges for Kohler faucets are the most common source of repeat drips we see, because the tolerances on the ceramic discs aren’t held as tight. For things like supply lines, stops, and drain assemblies, a quality aftermarket equivalent is fine and we’ll say so. We don’t claim to stock Kohler parts and we don’t carry them on a truck. What we do is spec the right part number up front so it’s ordered once and correct.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Kohler Home Additions & ADU Is Failing
- A Kohler faucet in the new bath drips from the spout with the handle off. That’s the ceramic cartridge, and in Glendale’s hard water it’s usually mineral scoring on the disc faces rather than a worn O-ring. Hard water here runs mineral-heavy, and a cartridge that would last ten years in a softer market can start weeping in three or four.
- The shower trim sits loose or won’t tighten against the tile. Almost always a trim and rough-in mismatch, or a rough-in set too deep in the wall during framing. Neither is a trim defect. The valve body has to come back out to the right depth, and that means opening the wall.
- Water pools at the base of a Kohler undermount sink in the kitchen. The sink clip or the sealant bed has failed, and on a new addition that often traces to a cutout that was sized to the sink’s outer flange instead of its interior bowl spec. The fix is re-setting the sink, not replacing it.
- A Kohler toilet in the ADU rocks on the flange. The closet flange was set below finished floor height during the pour, so the wax seal never compresses evenly. It’ll leak at the base long before it clogs.
- Pressure-balance valve hunts hot and cold when someone flushes. The balancing spool inside the valve is sticking, usually from debris that got into the line during construction and never got flushed out. A new-build flush-out before the cartridge goes in prevents most of these.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Glendale, here’s what the work actually costs. These are installed ranges, parts plus labor, and they include pulling the permit where one is required and having the inspection signed.
| Scope | Installed Range (Glendale) |
|---|---|
| Home Addition (Kohler bath/kitchen package included) | $45,000 – $130,000 |
| ADU Construction | $90,000 – $220,000 |
| Garage Conversion | $30,000 – $80,000 |
| Kohler cartridge or trim swap (single fixture) | Quoted per job after we identify the part number |
| Kohler shower valve rough-in correction (wall open and close) | Quoted per job after we identify the part number |
What drives the range on an addition or ADU is foundation and framing more than fixtures, but the Kohler package matters: carrying a full bath and kitchen through in Kohler versus mixing brands changes the number. What’s included on our side is the written scope, written allowances, and written change orders before any scope change touches the job. What’s not included is anything we haven’t put on paper first. Every completed job is backed by our written 90-Day Done Right Promise; if something’s not right, one call brings Tom back.
DIY or Call Us?
Some of this you can safely check yourself. Open the cabinet under a dripping Kohler faucet and look for water tracking down a supply connection. Shut the water off at the stop and see whether the drip stops. Jot down the model number off the trim escutcheon. That’s information, and it makes the call shorter.
Where it goes wrong: anything behind the wall. A shower valve swap means shutting the water to the house, opening the wall, and re-sweating or re-pressing a connection inside a wet wall. Get that wrong and you’re not looking at a leak, you’re looking at a soaked ceiling below it six weeks later. On a new addition or ADU, a mis-set rough-in also means the tile has to come off to correct it, and that’s a job nobody wants to do twice. We’d rather you call before you open the wall than after. Call (844) 560-4526 and we’ll tell you straight whether it’s a part or a rework.
FAQs
How long should a Kohler cartridge last in Glendale? Kohler’s ceramic cartridges are rated for years of service, but in Glendale’s mineral-heavy water we typically see them start weeping at the three-to-five-year mark rather than the ten-plus you’d get in a softer water market. A whole-house softener extends that noticeably. Call (844) 560-4526 for an exact quote on the swap, and the estimate is free.
Can it be repaired instead of replaced? Often, yes. A cartridge can usually be swapped without touching the valve body, and a loose trim can sometimes be corrected with a trim extension kit rather than opening the wall. A rough-in set at the wrong depth can’t be repaired, though, and that one has to be re-set. Call (844) 560-4526 and we’ll tell you which one you’re looking at.
How long does the swap take? A single Kohler cartridge or trim swap is a short visit, typically under an hour of actual work. A shower valve correction that requires opening and closing the wall runs longer and depends on what’s behind the tile. We’ll give you the window in writing before we start. Call (844) 560-4526 for an exact quote.
How do you source the Kohler part? We pull the model number off the fixture or the spec sheet, verify it against Kohler’s published spec for that rough-in and trim, and order it once. We don’t claim to stock Kohler parts and we don’t carry them on a truck. We also work with KraftMaid, Cambria, and Silestone for the kitchen and trim side of an addition, so the whole package can be spec’d together.
If you’re planning an addition or ADU in Glendale and want the Kohler package spec’d right the first time, or you’ve got a Kohler fixture in an existing build that’s failing, give us a call at (844) 560-4526 for a free estimate. We’ll look it up with you, put the scope in writing, and tell you honestly whether it’s a part or a rework. Barrett & Sons Construction Glendale proudly serves local communities and is owner-operated from day one; Tom publishes his name, his address, and his license number, and you’re welcome to look them up before you sign anything.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.