Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Fence Installation: The Glendale Owner’s Guide
KraftMaid fence installation in Glendale runs $3,500 – $9,000 installed, depending on lineal footage, material, and grade changes on your lot. KraftMaid builds its fence systems to tight tolerances, so a failing post, gate hinge, or panel is usually a fitting problem, not a materials problem. Most Glendale owners notice it the same way: a gate that drags on the Chevy Chase Canyon side yard after a wet winter, or a panel that pulls loose from its post along a slope in Glenoaks. If the fence is holding but the hardware, posts, or gates aren’t, we match the correct KraftMaid-compatible part and set it right.
Which KraftMaid Models This Applies To
KraftMaid fence lines vary by width and height sizing, rail spacing, and gate hardware series, so the part has to match the model, not just the look. Before we quote anything, we read the label on the inside face of a rail or the top cap – KraftMaid runs a model sticker and a series code there – and we measure post centers and rail thickness with a tape, because a part that’s a quarter-inch off won’t sit flush.
Here’s the OEM-versus-aftermarket call we make with Glendale owners. For gate hinges, latches, and post caps tied to a specific KraftMaid series, the OEM part is the safe move: an aftermarket hinge with different screw spacing means drilling new holes, and on a post that’s already weathered, that’s how cracks start. For panels and pickets, a quality aftermarket equivalent that matches the rail profile is often the smarter buy, and we’ll tell you when it is. KraftMaid compatibility isn’t about brand loyalty – it’s about whether the part fits the rail spacing and post size you already have.
If your fence shares a wall with cabinetry work, we also handle Cambria, Silestone, and Kohler in the same visit. We’re an independent contractor and not affiliated with KraftMaid; we install and source what fits your model.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Fence Installation Is Failing
A gate that sags and drags the ground is a hinge or post-settlement problem, not a latch problem – the hinge is worn or the post has shifted. Tightening the latch never fixes it.
- Posts leaning after wet weather. Glendale’s clay-heavy soil swells in the rainy season and shrinks in summer, and a post set shallow rocks loose over time. Your soil, not your fence brand, is the culprit.
- Rails pulling away from posts. Failed fasteners or rusted brackets let a rail walk out of its mortise. Left alone, the panel drops and the post takes the load it wasn’t built for.
- Gate hinges grinding or squealing. Grit and worn hinge pins are the usual cause. On an exterior KraftMaid gate, the hinge takes the brunt of every swing.
- Panel racking on a slope. Glendale lots step up toward the Verdugo foothills, so a square panel forced onto sloped ground twists and loosens. You’ll see daylight through the joints.
- Soft or splintered wood at the base. Ground contact holds moisture; over years the wood softens below grade. Once the base goes soft, no part swap saves the post.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most KraftMaid fence work we do in Glendale lands between $3,500 and $9,000 installed. That’s parts plus labor, written line-item before we start. What moves the number: lineal footage, how many posts need resetting versus just new hardware, whether the ground is level or stepped, and whether you need a picket-only repair or a full panel.
- Hardware-only fix – hinges, latches, brackets, fasteners: small and quick.
- Post reset or replacement – concrete work and soil handling drive this up.
- Full fence installation – at the $3,500 – $9,000 range depending on footage and material.
Every price change arrives as a written change order before we touch the job. Every eligible job gets permits pulled and inspections signed, because the permit inspector works for you. The work is backed by the 90-Day Done Right Promise – if it isn’t right, one call brings Tom back.
DIY or Call Us?
You can safely inspect a lot of this yourself. Run your hand along the rail-post joints, check for movement, look for rust at the fasteners, and watch the gate swing to see where it catches. Reading the KraftMaid model label and taking a few measurements saves us both time.
Where DIY goes wrong is at the post and gate. Re-hanging a heavy gate on a weathered post, or digging and resetting a post to the right depth in Glendale clay, is where a weekend project turns into a broken gate and a leaning fence. A gate that swings on a bad hinge is heavy, and it’s easy to get hurt. If the rail is pulling or the post is loose, that’s the point to stop and call – we’ll tell you honestly whether it needs a part or a reset.
Call (844) 560-4526 for a free estimate, and we’ll bring a second look at whatever estimate you already have.
FAQs
A well-set KraftMaid fence in Glendale typically holds 15 to 25 years depending on material and how it’s maintained against the region’s dry summers and wet winters. Posts set properly in deep clay last longest; a shallow-set post can go in a handful of seasons. Call (844) 560-4526 for a free estimate – estimates are free.
Often yes – most hinge, latch, and bracket failures are a part swap, not a full replacement. If the post is still solid and only the hardware wore out, that’s a small fix. Call (844) 560-4526 for an exact quote – estimates are free.
A hardware swap is usually a half-day, while a post reset or full panel replacement can run a full day or more depending on soil and access. Call (844) 560-4526 to schedule your free estimate and get a firm time.
We read your model label and series code, measure the rail and post, then match the correct OEM or quality aftermarket part for your line. We don’t carry stock on a truck; we source the specific part your model needs. Call (844) 560-4526 – estimates are free.
If your Glendale fence needs a part matched and set right the first time, call Barrett & Sons Construction Glendale at (844) 560-4526 for a free estimate. We’re owner-operated, the crew is background-checked, permits get pulled, and every price change is in writing before a nail moves. You can also ask about our permanent 10% Senior & Veteran discount and no trip charge inside the county.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.