Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Master Halco Home Additions & ADU: The Glendale Owner’s Guide
If you’re building a home addition or ADU and you want it framed, weather-tight, and permitted correctly, we handle that work in Glendale, with installed pricing typically landing between $45,000 and $130,000 depending on whether you’re adding a room or a full second dwelling. Master Halco isn’t the structural system here – it’s the fencing, gates, and access hardware around the build, and that’s where Glendale owners tend to discover a problem: the gate latch that won’t catch, the post that’s leaning six months after the fence went up, the driveway gate dragging on a slab that shifted. Usually you find it on a Saturday when the gate won’t close, or when a fence post starts working loose after a rain.
Which Master Halco Models This Applies To
Master Halco covers a lot of ground, and the part you need depends entirely on which line you have. Their residential lines run aluminum ornamental, steel ornamental, vinyl, and chain link, plus gate hardware packed separately from the panels. The fastest way to identify what you’re working with: check the post cap or the box label for a series number, then measure post spacing center-to-center and the panel width – most residential aluminum and steel runs at 6-foot or 8-foot panel sections, and vinyl is usually 6-foot with 5×5 or 4×4 posts. One compatibility gotcha we see in Glendale: eyeball-matching a latch to a 2-inch post when yours is actually 2.5-inch schedule 40, so the hardware won’t seat without a reducer. OEM hardware fits the first time; a quality aftermarket equivalent can work and often runs cheaper, but only if the post size and hinge backset match exactly. On a build like this, we also install KraftMaid, Cambria, and Silestone for the interior finishes.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Master Halco Home Additions & ADU Is Failing
These are the symptoms that mean a fence or gate component needs attention around a Glendale build:
- Gate sags and drags on the ground. Hinge plates have loosened or the post has settled – common in Glendale where expansive clay soil shifts with the wet and dry seasons.
- Latch won’t engage or pops open. The strike has moved out of alignment, usually because the gate leaf has racked a fraction of an inch over time.
- Posts leaning after rain. Footings were set shallow or the soil washed out – a 24-inch footing depth is the practical floor around here, and anything shallower will move.
- Rust streaks or powder-coat flaking on aluminum or steel. Scratch damage that went unsealed, or hardware of a different metal causing galvanic corrosion at the contact point.
- Vinyl panels bowing or popping from the rails. Heat expansion in a Glendale summer, or rails that were cut too tight with no room to move.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For the addition or ADU itself, Glendale installed pricing runs from $45,000 to $130,000 depending on square footage, foundation, and finishes. For the fence and gate hardware that supports it, you’re looking at hardware-only parts in the low hundreds and a full post or gate-section replacement higher than that once labor is in. What drives the range: whether it’s a single latch swap or a full post reset, whether the footing has to be dug out, and whether the gate needs re-hanging. We price parts and labor as separate lines so you can see exactly what you’re paying for. Every price change comes as a written change order before work happens, and the work is backed by our 90-Day Done Right Promise. Estimates are free.
DIY or Call Us?
A latch swap or a hinge screw snug-up is something a careful owner can do. Where it goes wrong: digging out and re-setting a post on a clay-heavy Glendale lot without getting the footing depth and drainage right, which is how you end up with the same lean next spring. And a gate under load is heavier than it looks – a sagging aluminum or steel gate that comes off its hinges can injure someone, so if the post is moving, stop and call. Our technicians have up to 28 years of experience with these systems. We’re an independent service provider, not affiliated with Master Halco. Call (844) 560-4526 and we’ll tell you honestly whether it’s a hardware fix or a footing job.
FAQs
How long should a Master Halco fence or gate last in Glendale? A properly footed aluminum or steel run holds 20-plus years here; vinyl often 15 to 20. The hardware and footings fail before the panels do, which is why we check those first. Call (844) 560-4526 for an exact assessment – estimates are free.
Can the part be repaired instead of replaced? Often yes. A misaligned latch, a loose hinge, or a single popped panel can usually be repaired rather than replaced. A bent post or a failed footing means replacement. Call (844) 560-4526 and we’ll give you a straight answer.
How long does the swap take? A latch or hinge swap is often done in an hour or two. A post reset or gate re-hang takes longer, and we’ll tell you the window up front. Call (844) 560-4526 to schedule your free estimate.
How do you source the part? We match by series number, post size, and panel dimension to the correct Master Halco-compatible hardware, and we’ll show you the part and price in writing before we order. Call (844) 560-4526 for a quote.
Call (844) 560-4526 for a free estimate on your Glendale home addition or ADU and the fence and gate work around it – a live person answers, and we walk the site with you before anything is quoted.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.