A Barrett company - serving Glendale, CA

Owens Corning Kitchen Remodeling in Glendale, CA

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Owens Corning Kitchen Remodeling: The Glendale Owner’s Guide

If you’re pricing Owens Corning kitchen remodeling in Glendale, a full kitchen remodel typically runs $14,000 – $45,000 installed, and a small kitchen comes in at $9,000 – $20,000. Owens Corning doesn’t make the cabinets, counters, or doors themselves – it makes the insulation, underlayment, and moisture-resistant substrates that go behind and under those surfaces – so “Owens Corning kitchen remodeling” almost always means the hidden layer failed, not the pretty layer. Most Glendale owners find out the hard way: a soft spot under the sink that flexes when they step on it, a backsplash tile that pops loose in a straight line, or a musty smell after the first rain that won’t go away no matter how much they clean.

Call (844) 560-4526

Which Owens Corning Models This Applies To

Owens Corning’s kitchen-relevant products fall into a few families: FOAMULAR extruded polystyrene rigid board (the common pink sheets used behind tile backer and under slab), the PINK fiberglass batts used in interior and exterior kitchen walls, and their moisture-resistant drywall and underlayment lines. Series names and thicknesses matter more than brand loyalty. FOAMULAR comes in 1/2″, 3/4″, 1″, 1.5″, and 2″ thicknesses, and the compressive strength rating (expressed as “25”, “40”, “60”, “100” PSI) is stamped on the face – the 40 PSI board is the one you want under a tile floor, not the 25. Fiberglass batts are labeled by R-value and width; a kitchen exterior wall in Glendale’s climate zone typically calls for R-13 to R-15 in a 2×4 cavity, R-19 to R-21 in a 2×6.

To match the right replacement, look for the printed label on the face of the board or the paper flange of the batt – the R-value, thickness, and PSI rating are all there. If the label is gone, a tape measure and a look at the cavity depth will tell you what was originally installed. On the OEM-versus-aftermarket question: for FOAMULAR and PINK fiberglass, brand-matched replacement is the correct call because the thickness, density, and vapor-permeance are tuned together. For underlayment and backer boards, a quality equivalent from a name you can verify (KraftMaid, Cambria, and Silestone are the surface brands we install in Glendale kitchens) is fine as long as the spec sheet matches. Knife-and-fork substitutions are where moisture problems start.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Owens Corning Kitchen Remodeling Is Failing

  • Soft, spongy floor tile near the dishwasher or sink. The underlayment board has taken on water and lost its compressive strength – common when the original install used 25 PSI FOAMULAR under a tile floor instead of 40 PSI.
  • Backsplash or counter tile lifting in a straight horizontal line. That’s not a tile problem, it’s a substrate problem – the backer or foam behind it has shifted or swelled, and the thinset let go along the seam.
  • Musty smell in the kitchen after rain, strongest near exterior walls. Wet fiberglass batts lose their R-value fast and don’t dry out once the paper facing is soaked. Glendale’s hot, dry summers followed by winter rains create the perfect swing for moisture to get trapped and stay.
  • Visible pink or blue foam crumbled or powdery behind an outlet or under a cabinet toe-kick. UV exposure or long-term water contact breaks down extruded polystyrene; once it’s chalky, it’s not insulating anything.
  • Cold spots on the kitchen floor in winter over a slab or unheated crawlspace. Foam board under the floor was either never installed or was installed at the wrong thickness – the 1/2″ board used where 1″ was specified shows up as a chill you can feel through socks.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed pricing for the Owens Corning work depends on how much has to come out to get the new layer in. A full kitchen remodel that includes replacing failed substrate and insulation runs $14,000 – $45,000 in Glendale. If the failure is contained to one area – a backsplash, an island base, a floor section under the sink – the standalone line items apply: backsplash installation $800 – $2,500, kitchen island installation $3,000 – $10,000, cabinet installation $4,000 – $13,000, countertop installation $2,000 – $6,500. Small kitchens where the whole substrate is being refreshed run $9,000 – $20,000.

What drives the range: whether the failed layer is behind tile (tile has to come out to fix the substrate, then go back), whether a permit is required for any electrical or plumbing relocation inside the kitchen, and whether the moisture source was fixed or just covered up. Our quotes are line-itemed – materials, labor, and any allowance for tile or counters, all written down before we start. Every eligible job gets permits pulled and inspections signed. Every completed kitchen is covered by the written 90-Day Done Right Promise. Reach us at (844) 560-4526 for a free estimate.

DIY or Call Us?

What a homeowner can safely check: the printed label on the face of the foam board or batt to confirm R-value and PSI, the cavity depth, whether moisture is present (a cheap pin meter from the hardware store reads this in seconds), and whether the underlayment is soft underfoot. Those four checks take twenty minutes and tell you most of what a pro would learn on a first visit.

Where DIY goes wrong: pulling tile to chase a substrate without a plan for what’s under it, replacing fiberglass batts without addressing the water that soaked the old ones (you’ll be back inside that wall next winter), and reinstalling underlayment at the wrong thickness because the only board in stock at the store was the 1/2″ instead of the 1″. None of those are dangerous the way electrical or gas work is – the risk here is repeating the failure and paying twice. If the moisture source isn’t found and fixed first, no amount of new Owens Corning product will hold up. Call (844) 560-4526 and we’ll tell you honestly whether your situation is a Saturday project or a pro job.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 560-4526
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Barrett & Sons Construction Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch