Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Glendale Owner’s Guide
If you’re working with a Schluter system under a driveway or paver assembly in Glendale, we install and repair the drainage and edge profiles that keep water moving away from your slab and your pavers locked where they belong. Installed paver driveway work in Glendale runs $7,000 – $18,000 depending on square footage, base prep, and drainage complexity, and paver patio installation runs $3,500 – $11,000. We’re an independent contractor, not affiliated with Schluter, and we schedule these as planned projects rather than same-day calls.
Most Glendale owners find out something’s wrong the same way: after a winter rain, water stands in a low corner of the driveway instead of running off, or a run of pavers near the edge starts rocking when you walk on it. Usually that’s not the pavers – it’s the profile underneath that was supposed to carry water away and hold the edge. Once that piece has shifted or clogged, the whole assembly starts working against itself.
Which Schluter Models This Applies To
Schluter’s drainage and paver profiles come in several families, and the two that matter most on driveways and paver work are the linear drainage channels (the KERDI-LINE and Troba lines, among others) and the edge and joint profiles (DILEX and Schluter’s paver edging lines). Each family has its own size grid, measured in millimeters – channel widths commonly span roughly 50 mm to 200 mm, and edge profiles are matched to your paver thickness in 2 to 3 mm increments. That’s the first compatibility gotcha: a profile sized for 20 mm porcelain isn’t the right part for a 60 mm concrete paver, and the part number changes with thickness even when the profiles look identical in the box.
Identify what you have before you shop. Look for the printed label on the profile body (often on the underside of the channel body or molded into the edge strip), measure the paver thickness with a caliper rather than eyeballing it, and note the outlet size on any channel drain. On the OEM-versus-aftermarket decision: for the channeled drainage pieces, we generally stay with Schluter-brand or a manufacturer-named equivalent, because the grate and body have to seat together and mismatched tolerances leak at the joint. For simple edge profiles, a quality galvanized or stainless equivalent often works fine.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Driveway & Pavers Is Failing
Five symptoms we see most often in Glendale driveways and patio work, and what each one actually means:
- Water pools against the house or in a low corner after rain. The drainage profile has shifted, the outlet is clogged with grit, or the slope was never set right under the channel. Standing water is the first thing you’ll notice.
- Pavers rock or feel loose along an edge. The edge profile has lost its anchor, usually because the base under it compacted or the fasteners pulled out of a soft substrate.
- A visible gap or step at the joint where pavers meet the channel. The profile height and the paver height no longer match, either from settling or from a part that was sized a few millimeters off to begin with.
- White efflorescence or staining in a line along the profile. Moisture is trapped and wicking through the joint, which points to a failed seal or a clogged channel rather than a cosmetic issue.
- A grate that rattles or sits proud of the pavers. The grate has warped or the seat has loaded up with debris; left alone, it cracks under a car tire.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Glendale, replacing failed drainage and edge profiles inside a paver assembly typically falls inside the paver driveway installation range of $7,000 – $18,000 when a chunk of the assembly has to come up, or inside driveway replacement at $5,000 – $14,000 when the base and profile both need redoing. A localized profile-and-joint repair runs less – a driveway sealing pass to protect a freshly repaired assembly runs $250 – $700.
What drives the range: how many linear feet of channel need replacing, whether pavers can be lifted and reset or must be replaced, base condition, and whether the outlet has to be re-routed to a proper drain. We price parts and labor as separate line items in writing before we start, and any change arrives as a written change order. The work carries our 90-Day Done Right Promise.
For a sense of the full picture: a paver patio installation in Glendale runs $3,500 – $11,000, and a straight concrete driveway installation runs $4,500 – $12,000 if you’re weighing a fresh start over a repair.
DIY or Call Us?
You can safely check a few things yourself: clear debris from the channel and grate, confirm water flows toward the outlet with a garden hose, and measure your paver thickness if you want to price a part. What goes wrong for most owners is the re-set – lifting pavers, resetting the base, and getting the profile pitched so water actually drains instead of sitting. Do that wrong and you’re back to a pool in the driveway after the next rain, with a profile that’s now buried under a fresh set of pavers. This part isn’t a shock or gas hazard, but it’s unforgiving about slope and base compaction. If water is pooling or the edge is loose, call us at (844) 560-4526 and we’ll take a look.
FAQs
Twelve to twenty-five years is a realistic range, with the low end common in Southern California where summer heat cycling and winter rain stress the joint and the base. Profiles that stay clear of debris and drain properly last toward the top of that range; a clogged channel that holds water accelerates failure. Call (844) 560-4526 for an exact quote – estimates are free.
Often yes – a localized re-set of the edge or a cleared and re-pitched channel usually costs a fraction of a full replacement. If the base under it has failed or the profile is cracked, though, a repair won’t hold and replacement is the honest answer. We’ll tell you which one you’re facing after we look. Estimates are free.
A localized profile and joint repair typically runs a day or two, while pulling up and resetting a larger run of pavers over a repaired base usually takes several days. Weather and how many pavers need replacing drive the schedule, and we put the timeline in writing before we start. Call (844) 560-4526 to schedule your free estimate.
We order the specific profile to your measured paver thickness and outlet size from a supplier, and we confirm the part number with you before it’s ordered – no guessing at the box label. Parts and labor are line-itemed in the written estimate so you can see exactly what’s being installed and why. Call (844) 560-4526 for a free estimate.
We also service KraftMaid, Cambria, and Silestone for other parts of your project.
This is the kind of work an owner-operated crew handles on a planned schedule, with scope in writing and change orders in writing – the way Tom Barrett and his sons have run jobs for over 29 years, and the way we’ll handle yours in Glendale. Don’t skip the free second opinion on any written estimate you’ve already been given, and don’t miss our standing offers: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% senior and veteran discount. Call Barrett & Sons Construction Glendale at (844) 560-4526 to schedule your free estimate.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.