A Barrett company - serving Glendale, CA

Schluter Fence Installation in Glendale, CA

FenceFence
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Fence Installation: The Glendale Owner’s Guide

Fence installation featuring Schluter components and profiles in Glendale typically runs $3,500 to $9,000 installed, depending on fence length, height, material, and slope. Barrett & Sons Construction Glendale installs Schluter-compatible fence systems (and we’re an independent contractor, not affiliated with Schluter). The tell is almost always a trim piece or base profile that won’t snap back, a cap that’s lifted, or a run that hums and sways when your neighbor’s gate slams. Once water gets behind the profile, Glendale’s dry summers and winter rain events push the damage faster than most people expect. Call (844) 560-4526 for a free estimate.

Call (844) 560-4526

Which Schluter Models This Applies To

Schluter doesn’t make fence panels – it makes the trim profiles, edge systems, and finish components that fence installers and fabricators use to finish a run cleanly. So “which Schluter model” rarely means a single serial number. It means the specific profile you’re holding: a finishing cap, a base or edge strip, a corner piece. The most reliable way to identify it is the ink stamp or printed label on the underside of the profile, plus a physical measurement of the depth and width. Take a photo with a tape measure held against it before you call anyone. That measurement is what tells a supplier whether the profile is a standard dimensions line or a specialty size that has to be ordered.

The OEM-vs-aftermarket decision for Schluter is genuinely different than for, say, a garage door spring. The aftermarket situation here is thinner and quality varies more. If the profile is a standard trim piece and a local supplier carries a true match, the aftermarket cost savings can make sense. If it’s a specialty finish profile or a load-bearing edge component, matching the original spec matters more than saving twenty dollars on a part that will fail again in Glendale’s sun. We tell customers honestly that if we can’t verify a match, we’d rather order the correct component. Ask anyone who tried to force a near-match and re-did the work six months later.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Fence Installation Is Failing

  • A profile that won’t re-seat after you press it back. The tolerance on Schluter finish profiles is tight; once the material takes a permanent set, it stops gripping. That set usually starts with thermal cycling and UV exposure.
  • A cap or edge strip that lifts noticeably at the corners. Corner lift almost always means water has been getting behind the profile and pushing it out from below, or the fastener has worked loose at the change of direction.
  • A running sway or hum when the wind hits or a gate closes. That flex travels into the profile joints and starts cracking the finish. In a run over thirty feet on a slope, this is common and worth a look before the finish fails.
  • Chalky or powdery buildup on the exposed faces. This is what UV degradation looks like on finish components after several summers in Glendale. The part still works, but it’s on its way out and painting won’t reverse it.
  • Rust staining or a brown streak running down a profile. That streak points to the fastener underneath, not the profile itself. It’s a symptom worth tracing before you replace the cover piece.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A full fence installation with Schluter finish components in Glendale sits in the $3,500 to $9,000 range. That’s the lead figure this page reflects and it covers material, labor, hardware, and site cleanup. What separates a $3,500 job from a $9,000 job is linear footage, fence height, material choice, slope and grading, gate hardware, and how many corners the run needs. A short run on flat ground with a single gate lands near the bottom of that range; a long run on a slope with multiple corners and premium material lands near the top. Every price change during the job arrives in writing as a change order before any work continues. The allowance that isn’t on paper is a surprise waiting for a date. Our workmanship is covered by the written 90-Day Done Right Promise.

DIY or Call Us?

What an owner can safely do: identify the part, measure it, photograph the label, verify whether the profile has simply loosened or has taken a permanent set, and check the fasteners underneath for rust or movement. Those checks are safe and they’ll help you make a real decision instead of guessing. Where a DIY effort usually goes wrong is in the install itself: getting the profile seated with correct tension across a run, aligning corners so the profile doesn’t telegraph a crack in six months, and getting the fastener depth right on a slope. Fence components aren’t a high-tension hazard the way garage door springs are, but a badly seated profile on a run will cost more to redo than it would have cost to install correctly. If you have a profile in your hand and you’re not sure it’s the right match, call us at (844) 560-4526 – the estimate is free and we’ll tell you honestly whether the part is worth replacing or the whole run needs attention.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 560-4526
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Barrett & Sons Construction Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch