Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Roofing: The Glendale Owner’s Guide
Schluter shower and floor waterproofing components that show up inside a roofing assembly usually mean one thing: a tile or flat-roof detail above a bath, balcony, or covered entry has been built with a Schluter drainage or waterproofing layer instead of a conventional roof membrane. In Glendale, we install and repair these assemblies for $400 – $1,800 on a targeted repair, and roof replacement work in the same system runs $8,000 – $20,000. We don’t promise same-day work on planned roofing, but we answer the phone live around the clock and can usually get a free estimate scheduled fast.
Owners here tend to find the problem the same way. A water stain blooms on a bathroom ceiling below a tiled deck. A Schluter KERDI membrane over an exterior tile walkway lifts at a corner after a wet winter. Caulk lines around a roof-to-wall junction open up, and the next rain sends water sideways under the tile instead of down the drain.
Key Takeaways
- Confirm you have a Schluter waterproofing assembly, not a standard roof membrane, before ordering anything.
- Targeted repairs in Glendale run $400 – $1,800; full replacement of the assembly runs $8,000 – $20,000.
- Pull the original spec sheet and any leftover membrane scraps before you call. It saves guesswork.
- Barrett & Sons Construction Glendale is an independent contractor, not affiliated with Schluter.
Which Schluter Models This Applies To
Schluter doesn’t sell a “roof” line. What you’re actually tracking down is a waterproofing product from their wet-area or exterior-tile family that got used on a roof-adjacent surface. The common ones:
- KERDI – the bonded sheet waterproofing membrane, usually with the fleece side facing the thinset. Green with a grid printed on it.
- KERDI-BOARD – the rigid foam-backed board for walls and some exterior details.
- KERDI-LINE and KERDI-DRAIN – linear and point drains. Even these show up in exterior shower or balcony drains.
- DITRA and DITRA-HEAT – uncoupling membrane, sometimes misused as a roof underlayment.
- SCHIENE and other tile edge profiles – the trim pieces at tile transitions, often the first thing to fail in sun and freeze-thaw.
To identify the right part, look at the roll edge printing on any leftover membrane, or the label on the box if you kept it. KERDI comes in standard 5-meter (about 16.4 ft) and 30-meter roll lengths, and the membrane width is usually 39-3/8 inches. Measure the actual piece you’re replacing. The width matters because KERDI overlaps are typically 2 inches at seams.
On the OEM vs aftermarket decision: for Schluter specifically, we recommend staying with genuine Schluter components. Their system is designed to work as a complete assembly (membrane, thinset, drain flange, sealant, and profile), and mixing in a third-party membrane or generic sealant breaks that compatibility. The savings on a knockoff membrane rarely beats the cost of redoing a failed seam.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Roofing Is Failing
Here’s what we actually see on Glendale jobs. Match your symptom to the cause – it tells you what part you need.
- Lifted tile over a membrane edge. The membrane lost its bond at a terminator, usually because the original install skipped Schluter’s KERDI-FIX sealant at the outer edge. That’s a caulk-and-rebond job, not a tear-off.
- Water stain on the ceiling below a tiled deck or balcony. A seam opened. KERDI seams need the 2-inch overlap and a thinset bond; a dry seam lets water run under the tile, and Glendale’s wet-season rain finds it.
- Efflorescence (white powder) at grout lines. Ongoing moisture under the tile, not surface dampness. This is a membrane failure, not a grout problem.
- Ponding at a KERDI-LINE drain. Debris in the drain channel or a slope that was never set right. Sometimes the drain body itself needs replacing.
- Lifted or cracked SCHIENE edge profile. Sun and thermal movement. The profile is the sacrificial piece; replacing it is quick and inexpensive.
If you see soft or crumbling decking underneath, that’s different. That’s a structural call – stop and get an inspection before anyone installs new membrane over it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Glendale, a targeted repair to a Schluter waterproofing assembly typically runs $400 – $1,800. Full replacement of the assembly as part of a roof or deck rebuild runs $8,000 – $20,000, with roof repair alone at $400 – $1,800 and roof replacement at $8,000 – $20,000.
What drives the range:
- How much tile has to come up to reach the failure.
- How much of the membrane needs replacing.
- Whether the substrate behind it is sound.
- Whether the drain or profile needs replacing along with the membrane.
- Height and access at the work area.
Every quote you get from us is line-itemed. Parts, labor, and disposal are separate lines. If the price changes during the job, that change arrives as a written change order before any work happens. Our 90-Day Done Right Promise is written on every contract – if it’s not done right, Tom comes back and makes it right on one call.
DIY or Call Us?
If the issue is a failed caulk joint at a profile or a lifted SCHIENE edge piece, this is a safe, reasonable owner check. Look at it, note what you see, take a photo, and compare it to the spec sheet.
Where DIY goes wrong is at the membrane seams, drains, and anything involving cuts through a waterproofing layer. Removing tile to reach a KERDI seam, then re-bonding it correctly to Schluter specs, is not a weekend job. A bad patch under a tiled deck reads as a leak in three months, and the second repair costs more than the first would have. The scary part isn’t just a small leak, either. Water intrusion into a roof or wall cavity is a structural concern, and it’s not the kind of thing to eyeball.
If you’re not sure what failed, call (844) 560-4526. The estimate is free, and there’s no trip charge inside the county.
FAQs
A properly installed and maintained Schluter assembly generally lasts as long as the tile over it, often decades, in the dry Southern California climate. Sealant at edges and profiles is the short-lived piece – expect it to need touching up on a cycle rather than lasting forever. Sun exposure matters here, and Glendale gets a lot of it. Call (844) 560-4526 for a walk-through of your specific assembly.
Often yes. Localized failures at a membrane seam, a lifted profile, or a drain connection are frequently repairable for hundreds of dollars, not thousands. The exception is a failed membrane across a large area or rotted substrate underneath – that pushes the job toward replacement. Call (844) 560-4526 for a free second opinion on any written estimate, including one you already have.
A targeted repair usually takes half a day to a full day, depending on how much tile has to come up. A full replacement of the assembly runs multiple days, but nobody replaces a Schluter deck or roof in a single afternoon, and anyone who promises that is not being straight with you.
We identify the exact Schluter product from the roll printing, the label, or a measured sample, then order genuine Schluter components through their supply chain. We don’t carry parts on a truck. The right part comes from the right source, verified against the spec sheet before it goes on the job.
If you’re also looking at kitchen or bath work, we install KraftMaid, Cambria, and Silestone as well. Every job of ours gets permits pulled and inspections signed where required. We’re independent, licensed, and the Barrett & Sons name is on the truck – right here in Glendale.
Call (844) 560-4526 to schedule your free estimate. A live person answers, day or night. Ask about our $40 Off Any Repair Over $200 offer and our permanent 10% Senior & Veteran discount.
Written by the team at Barrett & Sons Construction Glendale, serving Glendale and nearby areas.